572161
9
Zoom out
Zoom in
Previous page
1/90
Next page
English
8
4. Extension bar: Code No. 873633
The extension bar is convenient for working in very
restricted spaces or when the socket provided cannot
reach the bolt to be tightened.
CAUTION
when the extension bar is used, the tightening torque
is reduced slightly compared with the ordinary socket.
5. Universal joint:Code No. 992610
The universal joint is convenient for impacting nuts
when there is an angle between the socket and
wrench, or when working in a very narrow space.
6. Duct Socket:
This is used for tightening bolts and nuts on flange
sections of air conditioners, type ducts, etc.
7. Corner attachment (Model EW-14R)
Use this attachment only when the machine is applied
to the nut or bolt at the right angle.
8. Bit adaptor: Code No. 991476
This is used for tightening small screws (M6 – M8).
NOTES
(1) This adaptor is set only on the anvil (drive angle) of
the main unit. The bit adapter cannot be attached to
the special accessory anvil (square drive).
(2) Before starting work with the adapter, tighten a few
screws with it to make sure it’s tightening with the
appropriate torque.
(3) Tightening speed will be greatly reduced when driving
wood, tapping or other similar screws.
Optional accessories are subject to change without notice.
APPLICATION
Tightening and loosening of all types of bolts and nuts,
used for securing structural items.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
UC12SD
Before using the impact wrench, charge the battery as
follows.
1. Insert the battery into the charger.
Insert the battery firmly while observing its direction,
until it contacts the bottom of the charger (See Fig. 3).
CAUTION
The UC12SD model is the exclusively designed
charger. This cannot charge batteries except the
specified batteries. It is possible to insert the batteries
other than the specified into the charger and it may
light up the pilot lamps. However, you are requested
to exercise utmost caution not to charge batteries
other than specified ones because these can not only
be charged but also such actions can result in the
malfuntion of chargers.
2. Connect the charger power cord to the receptacle.
Connecting the power cord will turn on the charger
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the power
cord from the receptacle and check the battery
mounting condition.
Code No.
Hexagonal width
across flats (mm)
993658 12
992613 13
992615 14
Applicable plus driver bit
L 6.35
Bit No. L (mm) Code No.
No. 2
45 955229
70 955654
No. 3
45 955230
70 955655
Bit No.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi WR12DAF3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WR12DAF3 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info