381594

Hitachi wr 14 dsl Manual

11
Zoom out
Zoom in
Previous page
1/96
Next page
English
10
3. Extension bar: Code No. 873633
The extension bar is convenient for working in very
restricted spaces or when the socket provided cannot
reach the bolt to be tightened.
CAUTION:
When the extension bar is used, the tightening torque
is reduced slightly compared with the ordinary socket.
4. Universal joint: Code No. 992610
The universal joint is convenient for impacting nuts
when there is an angle between the socket and
wrench, or when working in a very narrow space.
5. Duct Socket
This is used for tightening bolts and nuts on flange
sections of air conditioners, type ducts, etc.
6. Corner attachment (Model EW-14R)
Use this attachment only when the machine is applied
to the nut or bolt at the right angle.
7. Bit adaptor: Code No. 322752
This is used for tightening small screws (M6 – M8).
NOTE:
(1) This adaptor is set only on the anvil (drive angle) of
the main unit. The bit adapter cannot be attached to
the special accessory anvil (square drive).
(2) Before starting work with the adapter, tighten a few
screws with it to make sure it’s tightening with the
appropriate torque.
(3) Tightening speed will be greatly reduced when driving
wood, tapping or other similar screws.
Optional accessories are subject to change without notice.
APPLICATION
⅜ Tightening and loosening of all types of bolts and
nuts, used for securing structural items
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (see Figs. 1 and 2).
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charger’s
pilot lamp will blink in red. (At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger until the line
is visible, as shown in Fig. 3, 4.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously
in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals) (See
Table 3)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 3, according to the condition of the charger or
the rechargeable battery.
Code No.
Hexagonal width
across flats (mm)
993658 12
992613 13
992615 14
01Eng_WR14DSL_WE 6/19/08, 17:5010
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi wr 14 dsl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi wr 14 dsl in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info