572160

Hitachi WP14DSL Manual

11
Zoom out
Zoom in
Previous page
1/80
Next page
English
10
How to make the batteries perform longer
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION:
⅜ When the battery charger has been continuosly used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next
charging.
⅜ If the battery is recharged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
map light in green.
The battery will not be recharged. In such a case, let
the battery cool before charging.
⅜ When the pilot lamp flickers in red (at 0.2-second
intervals), check for and take out any foreign objects
in the charger’s battery installation hole. If there are
no foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
PRIOR TO OPERATION
1. Preparing and checking the work environment
Make sure that the work site meets all the conditions
laid forth in the precautions.
2. Checking the battery
Make sure that the battery is installed firmly. If it is at
all loose it could come off and cause an accident.
3. Installing the bit
Always follow the following procedure to install bit
piece and driver bit. (Fig. 5)
(1) Pull the guide sleeve away from front of the tool.
(2) Insert the bit piece and driver bit into the hexagonal
hole in the anvil.
(3) Release the guide sleeve and it returns to its original
position.
CAUTION:
⅜ If the guide sleeve does not return to its original
position, then the bit is not installed properly.
⅜ This product also comes equipped with a bit piece.
Make sure that the bit piece is inside of the hexagonal
hole in the main shaft, then install the bit. (Fig. 6)
HOW TO USE
1. Check the rotational direction
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit
counterclockwise. (See Fig. 7) (The
L
and
R
marks
are provided on the body.)
CAUTION:
The push button cannot be switched while the oil
pulse driver is turning. To switch the push button,
stop the oil pulse driver, then set the push button.
2. Switch operation
⅜ When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
⅜ The rotational speed can be controlled by varying the
amount that the trigger switch is pulled. Speed is low
when the trigger switch is pulled slightly and increases
as the trigger switch is pulled more.
3. Change rotation speed
As shown in Fig. 8, when the rotation switch-over
lever is slid to the lower side, the power mode (P) is
set. And when slid to upper side, the save mode (S) is
set.
Please use the save mode (S) when you want to lower
Maximum tightening torque.
CAUTION
In the work of the save mode (S), avoid the continuous
screw-tightening as temperature of electronic
components of the converter switch increases.
4. Tightening and loosening wood screws
Install the bit that matches the screw, line up the bit
in the grooves of the head of the screw, then tighten
it.
Push the oil pulse driver just enough to keep the bit
fitting the head of the screw.
CAUTION:
Applying the oil pulse driver for too long tightens the
screw too much and can break it.
Tightening a screw with the oil pulse driver at an
angle to that screw can damage the head of the
screw and the proper force will not be transmitted to
the screw.
Tighten with this oil pulse driver lined up straight
with the screw.
5. Number of screws tightenings possible
Please refer to the table below for the number of
screw tightened possible with one charge.
These values may vary slightly, according to
surrounding temperature and battery characteristics.
6. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION:
⅜ When using the hook, hang up the power tool firmly
not to drop accidentally.
If the power tool is dropped, it may lead to an accident.
⅜ When carrying the power tool with hooked to your
waist belt, do not fit any bit to the tip of power tool. If
the sharp bit such as drill is fitted to the power tool
when carrying it with hooked to your waist belt, you
will be injured.
⅜ Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
(1) Removing the hook.
Remove the screws fixing the hook with Philips screw
driver. (Fig. 9)
(2)
Replacing the hook and tightening the screws.
Install securely the hook in the groove of power tool
and tighten the screws to fix the hook firmly. (Fig. 10)
Screw used
Battery
BSL1430
Wood screw ø4 x 50
Approx. 590
(Soft wood)
01Eng_WP14DSL_WE 9/24/09, 2:07 PM10
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi WP14DSL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WP14DSL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info