Manual Hitachi WH10DFL2 (page 5 of 140) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

572109

Zoom out

Zoom in

1/140

English

Table 1

Indications of the pilot lamp

Symbol mark

Pilot lamp

(red)

Before

charging

Blinks

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

While

charging

Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible

Flickers

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

Malfunction in the battery

or the charger

(2) Regarding the temperature of the rechargeable battery

The temperatures for rechargeable batteries are as

shown in the Table 2, and batteries that have become

hot should be cooled for a while before being recharged.

Table 2 Recharging ranges of batteries

Rechargeable batteries

Temperatures at which the

battery can be recharged

BCL1015 0°C – 50°C

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 3.

Table 3 Charging time (At 20°C)

Charger

Battery

UC10SL2

BCL1015 Approx. 30 min.

NOTE

The charging time may vary according to temperature

and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with UC10SL2

is taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the

battery

1 131

Charging 2 131

How to use the LED light 3 131

Mounting the bit 4 131

Reversing the rotational direction 5 131

Switch operation 6 132

Selecting accessories ― 133

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the impact driver is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

5. Storage

Store the impact driver in a place in which the temperature

is less than 40°C and out of reach of children.

0000Book_WH10DFL2.indb 50000Book_WH10DFL2.indb 5 2014/08/08 14:14:092014/08/08 14:14:09

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WH10DFL2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi WH10DFL2 Manual

Product: