Manual Hitachi WH 18 DL (page 9 of 86) (English, German, Dutch, French, Italian, Portuguese, Spanish)

79228

Zoom out

Zoom in

1/86

English

⅜ Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the

light equipped hook suspended from a waist belt.

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

1. Using the light equipped hook

The light equipped hook can be installed on the right

or left side and the angle can be adjusted in 5 steps

between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook E toward you in the direction of

arrow (A) and turn in the direction of arrow (B)

(Fig. 5).

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for use.

(2) Switching the hook position

CAUTION

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin (Fig. 6).

(b) Remove the hook E and spring F (Fig. 7).

and securely fasten with screw (Fig. 8).

NOTE

Pay attention to the spring F orientation. Install the

spring F with larger diameter G away from you

(Fig. 8).

(3) Using as an auxiliary light

(a) Press the switch H to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(b) The direction of the light can be adjusted within

the range of hook positions 1 – 5 (Fig. 9).

⅜ Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION

Do not look directly into the light.

Such actions could result in eye injury.

(4) Replacing the batteries

(a) Loosen the hook screw J with a phillips-head

screwdriver (No. 1) I (Fig. 10).

Remove the hook cover L by pushing in the

direction of the arrow (Fig. 11).

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly (Fig. 12).

with the protuberance of the hook cover L, press

the hook cover L in the direction opposite to that

of the arrow K shown in Fig. 11 and then tighten

the screw.

Use commercially available AAAA batteries

(1.5 V) O.

NOTE

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION

⅜ Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

⅜ Do not discard batteries together with normal trash

and do not throw batteries into fire.

⅜ Store batteries out of the reach of children.

⅜ Use batteries correctly in accordance with the battery

specifications and indications.

2. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button C.

The L-side of the push button is pushed to turn the bit

counterclockwise (See Fig. 4) (The

and

marks

are provided on the body).

CAUTION

The push button cannot be switched while the impact

driver is turning. To switch the push button, stop the

impact driver, then set the push button.

3. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

4. Change rotation speed

As shown in Fig.17, when the rotation switch-over

lever T is slid to the lower side, the power mode V (P)

is set. And when slid to upper side, the save mode U

(S) is set.

Please use the save mode (S) when you want to lower

Maximum tightening torque.

CAUTION

In the work of the save mode (S), avoid the continuous

screw-tightening as temperature of electronic

components of the converter switch increases.

5. Tightening and loosening screws (Impact driver)

Install the bit that matches the screw, line up the bit in

the grooves of the head of the screw, then tighten it.

Push the impact driver just enough to keep the bit

fitting the head of the screw.

CAUTION

Applying the impact driver for too long tightens the

screw too much and can break it.

Tightening a screw with the impact driver at an angle

to that screw can damage the head of the screw and

the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with

the screw.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

NOTE

Do not touch the protector, as it gets very hot during

continuous work.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WH 18 DL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi WH 18 DL

Hitachi WH 18 DL User Manual - English, German, Dutch, French, Italian, Portuguese, Spanish - 74 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi WH 18 DL Manual

Product: