571648

Hitachi WF4V Manual

7
Zoom out
Zoom in
Previous page
1/38
Next page
English
6
7. Protect your eyes with protective glasses.
Always wear protective glasses while working.
Drilling scatters plaster powder and tape dust,
which are dangerous if they get into your eyes
8. Watch out for wires and pipes in walls and ceilings.
When working on floors, walls, or ceilings, check
for wires and pipes ahead of time. Work carefully
to avoid shocks and explosions.
9. When the screw feed attachment is removed,
always use the correct driver bit for the screw size.
STANDARD ACCESSORIES
(1) Screw feed attachment .......................................... 1
(Assembled in main body)
(2) No. 2 Plus Bit .......................................................... 1
(Assembled in main body)
(3) Hook ........................................................................... 1
(4) Belt guide ................................................................. 1
(5) Rubber cover (B) ...................................................... 1
(6) Plastic case ............................................................... 1
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜ Screw driving into indoor gypsum board
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operation immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
10. When the screw feed attachment is removed, if
the screwdriver is positioned at an angle against
the tightening screw, the head of the screw may
be damaged or the fixed tightening force will not
transfer to the screw. Always position the
tightening screw and the screwdriver at a straight
angle and then tighten the screw.
SPECIFICATIONS
* Be sure to check the nameplate on product as it is subject to change by areas.
4. Preparing and checking the work environment
Make sure that the work site meets all the conditions
laid forth in the precautions.
5. Preparing the screws
Select screws appropriate to the application.
6. Bit checking and replacement
A No. 2 Plus bit is installed on this machine as a
standard accessory. Always inspect the bit to make
sure it is not damaged. Using worn bits can cause
screw-in malfunctions. Inspect the bit before work
and quickly replace it with a new one when it starts
to wear out. When the bit must be replaced due
to bit damage or any other reason, replace it
according to the instructions in Bit installation and
removal.
SCREW FEED ATTACHMENT INSTALLATION
AND REMOVAL
CAUTION
To prevent accidents, always switch off the switch and
unplug the power cord from the electrical socket before
installation or removing screw feed attachment.
1. Screw feed attachment removal
Secure the main body with one hand and turn the
screw feed attachment with another hand in the
direction of the arrow mark shown in Fig. 1.
Align the “
” mark of the main body and the
“
”mark of the screw feed attachment, then pull
the attachment in the direction of the arrow mark
shown in Fig. 2 to remove it.
NOTE
If the dust from the plaster adheres to the attachment
installation gate, it makes the attachment difficult
to remove. Clean the installation gate so the plaster
dust does not adhere.
Voltage (by areas)* (220V, 230V, 240V)
Power input 300 W
No-load speed 0 – 2300/min
Capacity
Screw size 4 mm
Screw length 25 – 41 mm
Tightening torque Maximum 1000 kg-cm
Tightening is M12 high tension bolt (strength grade 12.9).
Tightening time: 3 sec. Use hexagonal socket.
Bit shank size 6.35 mm Hex.
Weight (without cord) 1.8 kg
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi WF4V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi WF4V in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info