571643

Hitachi VTV-18A Manual

6
Zoom out
Zoom in
Previous page
1/41
Next page
5
English
8. Fixing the side handle:
Loosen the knob bolt on the side handle, and attach
the side handle to the gear cover in a position
convenient for drilling.
Match the projecting part of the handle to the groove
on the gear cover, and firmly tighten the knob bolt.
To remove the side handle, loosen the knob bolt
and rotate the handle.
To attach a depth stopper on the side handle, insert
the depth stopper into the U-shaped groove on the
side handle, adjust the position of the depth stopper
in accordance with the desired depth of the hole,
and firmly tighten the knob bolt.
PRACTICAL HANDLING PROCEDURES
1. Pressure:
Drilling will NOT be accelerated by placing heavy
pressure on the drill. Such action will only result in
a damaged drill bit, decreased drilling efficiency, and/
or shortened service life of the drill.
2. Using a large diameter drill bit:
When using the larger diameter drill bit, the larger
reactive force is applied on your arm. Be careful not
to lose control of the drill because of this reactive
force. To maintain firm control, establish a good
foothold, hold the drill tightly with both hands, and
ensure that the drill is vertical to the material being
drilled.
3. When drilling completely through the material:
When the drill bit bores completely through the
material, careless handling often results in a broken
drill bit or damage to the drill body itself due to the
sudden movement of the drill.
Always be alert and ready to release the pushing
force when penetrating the material.
4. Switch operation:
(1) VTP-18 :
By pulling the trigger switch and depressing the
stopper, the switch is held in the ON position for
continuous operation. To turn the drill OFF, pull the
trigger switch again and release.
(2) VTV-18 :
The rotational speed of the drill bit can be controlled
by varying the amount that the trigger switch is
pulled. Speed is low when the trigger switch is pulled
slightly and increases as the switch is pulled more.
Continuous operation may be attained by pulling
the trigger switch and depressing the stopper. To
turn the switch OFF, pull the trigger switch again to
disengage the stopper, and release the trigger switch
to its original position.
5. Precautions on Boring
The drill bit may become overheated during
operation; however, it is sufficiently operable. Do
not cool the drill bit in water or oil.
6. Caution concerning immediately after use
Immediately after use, while it is still revolving, if
the Drill is placed on a location where considerable
ground chips and dust have accumulated, dust may
occasionally be absorbed into the Drill mechanism.
Always pay attention to this possibility.
MAINTENANCE AND INSPECTION
1. Inspecting the Drill Bit:
Continued use of a worn and/or damaged drill bit
will result in reduced drilling efficiency and may
seriously overload the drill motor. Inspect the drill
bit often and replace it with a new bit as necessary.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Inspecting the carbon brushes (Fig. 3)
The motor employs carbon brushes which are
consumable parts. Since excessively worn carbon
brushes can result in motor trouble, replace the
carbon brushes with new ones having the same
carbon brush No. shown in the figure when they
become worn to or near the “wear limit”. In addition,
always keep carbon brushes clean and ensure that
they slide freely within the brush holders.
4. Replacing carbon brushes:
⅜ Disassembling:
(1) Loosen the three screws on the handle cover, and
remove the handle cover. Remove the holder plates,
which keeps the brush holders in place, by removing
the stopper screws.
(2) Lift out the brush holders together with the carbon
brushes, while being very careful not to forcibly pull
the lead wires within the brush holders.
(3) Withdraw the brush terminals, and remove the
carbon brushes from the brush holders.
⅜ Reassembling:
(1) Place new carbon brushes into the brush holders,
and connect the brush terminals to the carbon
brushes.
(2) Return the brush holders and other parts to their
original positions, as illustrated in Fig. 4, press the
holder plates into position, and fasten it with the
stopper screws.
(3) Place the lead wire in the specified position.
Be very careful not to allow the lead wire to contact
the armature or rotating parts of the motor.
(4) Replace the handle cover, while being careful to
ensure it does not pinch the lead wire, and secure
it firmly with the three screws.
CAUTION
Should the lead wire be pinched by the handle cover
or come in contact with the armature or rotating
parts of the motor, a serious danger of electric shock
to the operator will be created. Exercise extreme
caution in disassembling and reassembling the
motor, follow the above procedure exactly.
DO NOT attempt to disassemble any parts other than
those necessary to effect replacement of the carbon
brushes.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi VTV-18A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi VTV-18A in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info