135080
26
Zoom out
Zoom in
Previous page
1/39
Next page
4 Confirm with OK .
TIMER
VPS
DATE REP. PROG. START PDC END
21 MO-FR 01 20:00 ] 21:30
________________________________
REP.pSELECT STOREpOK
The following message appears on the screen: 'SELECT
PROG. NR.'
* The programme number of the TV channel has not yet
been assigned to the PlusCode number. Using the number
buttons
0-9 on the remote control, select the
corresponding programme number (programme name) of
the TV channel and confirm with
OK .
The following message appears on the screen:
'PLUSCODE NUMBER NOT VALID'
* The entered PlusCode number is incorrect. Correct your
instructions or end with
MENU .
* Check the time/date (see chapter 'Installing your video',
section 'Setting the time and date').
The following message appears on the screen: 'MO-FR
PROGRAMMING NOT POSSIBLE FOR WEEKEND'
* A daily recording was entered for the wrong day. Daily
programming can only be used for recordings to be made
from Monday to Friday.
5 The decoded data appears after confirmation. You can go
back to change the data. Select the corresponding input
field using
P or Q . Change the data with
;P+ , P- = or with the number buttons 0-9 .
Switching on 'VPS/PDC' in the 'START' input field
Select the 'START' input field using
P . Using
SELECT switch on 'VPS/PDC' (']' lights up). If you press
SELECT again, you will switch 'VPS/PDC' off (']' goes out).
6 When all informations are correctly, confirm with
OK .
The programming information is stored in a TIMER block.
7 Insert a cassette with an intact security tab (unprotected).
8 Switch off with STANDBY m .
The programmed recording will only function when the
video recorder is switched off with
STANDBY m .
If any of the TIMER blocks are in use, '
k' will light up on
the video recorder display.
Problems and solutions for
programmed recordings
The video recorder will not operate
* While a programmed recording is being made, you cannot
operate your video recorder manually. If you want to cancel
the programmed recording, press
STANDBY m .
'SWITCH TO STANDBY- TIMER RECORDING' flashes on
the TV screen
* The video recorder was switched on several minutes
before the start of a programmed recording.
Switch off the video recorder with
STANDBY m .A
programmed recording (timer) will only function if the video
recorder is switched off.
Cassette is ejected during recording
* The end of the tape was reached during recording.
Error message: 'NO CASSETTE'
k' will flash in the video
recorder display
* No cassette was inserted. Insert a cassette and switch off
the video recorder using
STANDBY m .
Cassette was ejected as soon as the
OK button was
pressed
* A cassette was inserted with the security tab removed.
Undo the erase protection (chapter 'Manual Recording',
section 'Preventing accidental erasing of cassettes') or
insert a different cassette.
Error message: 'ALL TIMERS OCCUPIED'
* If this error message appears after pressing
TIMER , then
all TIMER blocks are already programmed. No more
recordings can be programmed. If you want to clear a
programmed recording (TIMER block), select it with
;P+ or P- = and then press CLEAR (CL) .
23
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi vt fx 140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi vt fx 140 in the language / languages: English as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi vt fx 140

Hitachi vt fx 140 User Manual - German - 37 pages

Hitachi vt fx 140 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info