135080
10
Zoom out
Zoom in
Previous page
1/39
Next page
Initial installation
This chapter shows you how to start the initial installation. The
video recorder automatically seeks out and stores all available
TV channels.
'Aim' correctly
In the following sections, you require the remote control for
the first time. When using, always aim the front of the
remote control at the video recorder and not at the TV set.
Connecting additional devices
After you have connected additional devices (satellite
receiver, etc.) through the aerial cable, switch them on. The
automatic channel search will recognise them and save
them.
1 Confirm the image on the TV screen by pressing the
OK button on the remote control.
Autoinstall starts. This picture will appear on the screen:
AUTO INSTALL
SEARCHING
00 TV CHANNELS FOUND
ƒƒƒƒƒƒƒ__________________
PLEASE WAIT...
The video recorder does not find any TV channels
during the search
* Select channel 1 on the TV set. Can you see the saved TV
channel on the TV set?
If not, check the cable connection of the aerial (aerial
socket), video recorder, TV set.
* Please have patience.
The video recorder searches the entire frequency range in
order to find and save the largest possible number of TV
channels. It is possible that the TV channels in your country
are broadcast in a higher frequency range. As soon as this
range is reached during the search, the video recorder will
find the TV channels.
2 When 'Autoinstall' is complete, 'STORED' will briefly
appear on the TV screen.
The initial installation is now complete.
Check the date and time. Please read 'Setting the time and
date' in this chapter.
Satellite receiver
If you are connecting a satellite receiver, please read the
section 'Using the satellite receiver'.
Decoder
If you are connecting a decoder, you must install it as
described in the next section.
Decoder allocation
Some TV channels transmit encoded TV signals which can
only be viewed with a commercially purchased or hired
decoder without disturbances. You can connect such a
decoder (descrambler) to this video recorder. The following
function will automatically activate the connected decoder for
the desired TV channel.
How do I allocate the decoder with Easy Link?
If your TV supports the 'Easy Link' function, the decoder
must be allocated to the respective TV channel on the TV
(see TV operating instructions).
1 Switch the TV on. If applicable, select the programme
number for the video recorder operation.
2 Use the buttons
;P+ , P- = on the video recorder or
the number buttons
0-9 on the remote control to select
the TV channel which you would like to allocate the
decoder to.
3 Press the button
MENU on the remote control. The main
menu will appear.
4 Use the buttons
;P+ or P- = to select the line
'MANUAL SEARCH' and confirm with
OK .
MANUAL SEARCH
PROGRAMME NUMBER è P01 p
S-CHANNEL NO
CHANNEL NUMBER 21
DECODER OFF
TV SYSTEM AUTO
________________________________
EXITpMENU STOREpOK
5 Use the buttons P- = or ;P+ to select the line
'DECODER'.
6 Use the buttons
Q or P to select 'ON' (Decoder
switched on).
2. Installing your video recorder
7
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi vt fx 140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi vt fx 140 in the language / languages: English as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi vt fx 140

Hitachi vt fx 140 User Manual - German - 37 pages

Hitachi vt fx 140 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info