Manual Hitachi VB13Y (page 8 of 42) (English, German, Dutch, French, Italian, Portuguese, Spanish)

571430

Zoom out

Zoom in

1/42

English

Read handling instructions before use.

Avoid any work exceeding

the maximum capacities.

(Rebar diameter ø 13mm.)

Do not this electric power tools

in wet wether conditions.

Do not attempt to cut two rebars

at one time.

If the switch is turned off and

then immediately turned on

again, the motor may not start.

Wait for at least one full second

before attempting to turn the

motor on again after it has been

switched off.

Begin operation only after

ensuring that there are no people

within the turning range of the

material to be bent.

Never bring your hand close to

the cutter during operation.

HOW TO USE (CUTTING)

WARNING!

⅜ Note that the unit is not a hand held tool. Be absolutely

sure to use the unit only after placing it on stable

spots such as floor, ground, etc.

⅜ Never bring your hand close to the cutter during

operation.

⅜ Never bring your hand close to the reaction stoppers

A and B during operation.

⅜ Do not cut any materials other than the rebars. If you

attempt to do so, the material can splinter into pieces

and scatter.

⅜ Only cut the one piece of rebar at a time. It is

impossible to cut more than two pieces at one time,

and attempting to do so can damage the unit and

blades.

⅜ The bending roller moves even during cutting

operation. Never bring your hand close to the bending

roller.

1. Normal cutting (Fig. 3.)

(1) Turn the lever in the direction of the arrow mark and

open the cover.

(2) Set the setting dial at the “cut” position. (Turn the

setting dial all the way clockwise.) (Fig. 3.)

(3) Set the unit in the position shown in Fig. 3.

(4) Set the rebar to be cut on the lower cutter.

(Bending)

q Close the cover.

w Select the bending angle.

e Place a rebar.

r Pull the trigger.

(Cutting)

q Open the cover.

w Select CUT.

e Place a rebar.

r Pull the trigger.

(Returning Halfway)

q Select RETURN with the dial.

w Pull the trigger.

Refer to the Handling Instructions for details.

(5) When the rebar is set, make sure that either the

reaction stopper A or B is hitched to the rebar.

(6) Pull the switch trigger and cut the rebar.

CAUTION

⅜ For the sake of safe operation, this unit is designed

so that the switch cannot be inadvertently switched

on. When switching the tool on, press the lock button

and then pull the switch trigger (Fig. 2). If the switch

trigger is pulled without pressing the lock button

first, the switch may be damaged. Please use care

when switching the tool on.

⅜ Even after the cutting has been completed, continue

pulling the switch trigger until the motor starts to run

in the reverse direction and the cutter starts to return.

If the switch trigger is released too early, the cutter

will not return and the trigger will have to be pulled

again.

2. Removing the rebar during cutting operation. (Fig.

4.)

If the switch trigger is released in the middle of

cutting, the cutter can come to a stop at a halfway

position, jumming the rebar in the unit.

When this occurs, you can either pull the switch

trigger again and cut off the rebar, or you can free the

rebar by bringing the upper cutter back up to the

home position by carrying out the following

procedure. (Fig. 4.)

PICTGRAPH ILLUSTRATION AND

EXPLANATION

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi VB13Y in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi VB13Y Manual

Product: