Manual Hitachi UC14SD-01 (page 4 of 29) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

571368

Zoom out

Zoom in

1/29

English

CHARGING

Before using the power tool, charge the battery as follows.

1. Insert the battery in the charger.

Position the battery so that the nameplate faces

toward the nameplate of the charger and press in the

battery until it comes into contact with the bottom

plate. (See Figs. 1 and 2)

2. Connect the charger power cord to the receptacle.

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the AC outlet and check the

battery mounting condition.

About 1 hour is required to fully charge the battery at

a temperature of about 20°C. The pilot lamp goes off

to indicate that the battery is fully charged.

CAUTION

⅜ If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light. At that time cool the battery first, then

start charging.

⅜ The UC14SD is a charger to be used exclusively

for the EB1414 battery. Avoid charging batteries

with the charger other than the EB1414 battery.

While it is possible to insert the 7.2 V, 9.6 V, 12 V

and 24 V batteries into the charger lighting up the

pilot lamp, please note that no charging can be

made. Inserting a 14.4V battery into this charger

will commence charging. However, do not do so

since this may damage the battery and charger.

3. Disconnect the charger power cord from the

receptacle.

4. Hold the charger tight and pull out the battery.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

2. Cleaning of the charger

When the charger is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, as

they melt plastics.

3. Store idle charger

When not in use, the charger should be stored in dry,

high or locked-up place–out of reach of children.

4. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: – Neutral

Brown: – Live

As the colours of the wires in the mains lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi UC14SD-01 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi UC14SD-01 Manual

Product: