Manual Hitachi TCP27EPAP (page 12 of 64) (English, German, Dutch, French, Italian, Spanish)

571104

Zoom out

Zoom in

1/64

English

Angle transmission (Fig. 36)

Check angle transmission or angle gear for grease level about every

50 hours of operation by removing the grease ﬁ ller plug on the side

of angle transmission.

If no grease can be seen on the ﬂ anks of the gears, ﬁ ll the

transmission with quality lithium based multipurpose grease up to

3/4.

Do not completely ﬁ ll the transmission.

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions. For

further information please contact Tanaka dealer.

Daily maintenance

○ Clean the exterior of the unit.

○ Clean the chain oil ﬁ lter port.

○ Clean the groove and oil ﬁ lter port in the guide bar.

○ Clean the side case of saw dust.

○ Check that the saw chain is sharp.

○ Check that the bar nuts are suﬃ ciently tightened.

○ Make sure that the chain transport guard is undamaged and that

it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

Weekly maintenance

○ Check the starter, especially cord and return spring.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap. Adjust it to

0.6 mm or change the spark plug.

○ Clean the cooling ﬁ ns on the cylinder and check that the air

intake at the starter is not clogged.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline, and clean fuel ﬁ lter.

○ Clean chain oil ﬁ lter.

○ Clean the exterior of the carburetor and the space around it.

○ Clean the fan and the space around it.

○ Clean the muﬄ er of carbon.

CHAIN SHARPENING

Parts of a cutter (Fig. 37, 38)

WARNING

Gloves should be used when sharpening chain.

35. Top plate

36. Working corner

37. Side plate

38. Gullet

39. Heel

40. Chassis

41. Rivet hole

42. Toe

43. Depth gauge

44. Correct angle on top plate (degree of angle depends on chain

type)

45. Slightly protruding “hook” or point (curve on non-chisel chain)

46. Top of depth gauge at correct height below top plate

47. Front of depth gauge rounded oﬀ .

LOWERING DEPTH GAUGES WITH A FILE

1) If you sharpen your cutters with a ﬁ le holder, check and lower the

depth.

2) Check depth gauges every third sharpening.

3) Place depth gauge tool on cutter. If depth gauge projects, ﬁ le

it level with the top of the tool. Always ﬁ le from the inside of the

chain toward an outside cutter. (Fig. 39)

4) Round oﬀ front corner to maintain original shape of depth gauge

after using depth gauge tool. Always follow the recommended

depth gauge setting found in the maintenance or operator

manual for your saw. (Fig. 40)

GENERAL INSTRUCTIONS FOR FILING CUTTERS

File (48) cutter on one side of the chain from the inside out. File on

forward stroke only. (Fig. 41)

5) Keep all cutters the same length. (Fig. 42)

6) File enough to remove any damage to cutting edges (side plate

(49) and top plate (50)) of cutter. (Fig. 43)

SHARPENING ANGLES FOR SHARPENING SAW CHAIN

1. Part Number

90SG-40

90PX-40

2. Pitch 3/8”

3. Depth Gauge Setting 0.025"

4. Side Plate Filing Angle 80°

5. Top Plate Angle 30°

6. File Guide Angle 90°

000Book_TCS27EPAP(S)_WE.indb 12000Book_TCS27EPAP(S)_WE.indb 12 2014/06/04 15:21:582014/06/04 15:21:58

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi TCP27EPAP in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi TCP27EPAP Manual

Product: