571094

Hitachi TCH22EBP2-62ST Manual

8
Zoom out
Zoom in
Previous page
1/88
Next page
8
English
Lubricating the blade (Fig.12)
During trimming, sap adhering to the blade edge will increase load.
Use machine oil (or bicycle oil or the like) to lubricate the blade and
wipe the blade with a cloth. To prevent the blade from rusting, be
sure to lubricate the blade after use and when it will not be used for
an extended period of time before placing it in the blade case.
Gear case (Fig. 13)
Apply a good quality lithium based grease through the grease fi tting
until a small amount comes out between the cutting blades and the
gear case. Lubricate the grease from the grease nipple (indicated
by an arrow) next to the gear case using a commercially available
cartridge grease gun.
NOTE
Lubrication should be applied 3g at 20 hour intervals and more
frequently with heavy use.
Fuel fi lter (Fig. 14)
Remove the fuel fi lter from the fuel tank and thoroughly wash it in
solvent. After that, push the fi lter into the tank completely.
NOTE
If the fi lter is hard due to dust and dirt, replace it.
Cleaning the cylinder fi ns (Fig. 15)
When leaves get caught between cylinder fi ns (7), the engine may
overheat, resulting in lower output. To avoid this, always keep
cylinder fi ns and cylinder cover clean.
Every 100 operating hours, or once a year (more often if conditions
require), clean fi ns and external surfaces of engine of dust, dirt and
oil deposits which can contribute to improper cooling.
Cleaning the muffl er (Fig. 16)
Remove the muffl er and spark arrestor (if so equipped), and clean
out any excess carbon from the exhaust port or muffl er inlet every
100 hours of operation.
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until it stops.
Repair any damage which has resulted from use. Clean the unit with
a clean rag, or high pressure air hose. Put a few drops of two-cycle
engine oil into the cylinder through the spark plug hole, and spin the
engine over several times to distribute oil. Cover the unit and store
it in a dry area.
Maintenance schedule
Below you will fi nd some general maintenance instructions. For
further information please contact your Tanaka dealer.
Daily maintenance
○ Clean the exterior of the hedge trimmer.
○ Check the blade guide for damage or cracks. Change the guard
in case of impacts or cracks.
○ Check that the blade is sharp, and without cracks.
○ Check that the blade nut is suffi ciently tightened.
○ Make sure that the blade blunt guard is undamaged and that it
can be securely fi tted.
○ Check that nuts and screws are suffi ciently tightened.
Weekly maintenance
○ Check the starter, especially cord and return spring.
○ Clean the exterior of the spark plug.
○ Remove it and check the electrode gap. Adjust it to 0.6 mm, or
change the spark plug.
○ Clean the cooling fi ns on the cylinder and check that the air
intake at the starter is not clogged.
○ Check gear case is fi lled with grease.
○ Clean the air fi lter.
Monthly maintenance
○ Rinse the fuel tank with gasoline.
○ Clean the exterior of the carburetor and the space around it.
○ Clean the fan and the space around it.
MAINTENANCE
MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION
CONTROL DEVICES AND SYSTEM MAY BE PERFORMED
BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR
INDIVIDUAL.
Carburetor adjustment (Fig. 9)
WARNING
○ The cutting attachment may be spinning during carburetor
adjustments.
○ Never start the engine without the complete cleaner cover.
Otherwise the clutch can come loose and cause personal
injuries.
In the carburetor, fuel is mixed with air. When the engine is test run
at the factory, the carburetor is adjusted. A further adjustment may
be required, according to climate and altitude. The carburetor has
one adjustment possibility:
T = Idle speed adjustment screw.
Idle speed adjustment (T)
Check that the air fi lter is clean. When the idle speed is correct, the
cutting attachment will not rotate. If adjustment is required, close
(clockwise) the T-screw, with the engine running, until the cutting
attachment starts to rotate. Open (counter-clockwise) the screw
until the cutting attachment stops. You have reached the correct idle
speed when the engine runs smoothly in all positions well below the
rpm when the cutting attachment starts to rotate.
If the cutting attachment still rotates after idle speed adjustment,
contact Tanaka dealer.
Air fi lter (Fig. 10)
The air fi lter must be cleaned from dust and dirt in order to avoid:
○ Carburetor malfunctions.
○ Starting problems.
○ Engine power reduction.
○ Unnecessary wear on the engine parts.
○ Abnormal fuel consumption.
Clean the air fi lter daily or more often if working in exceptionally
dusty areas.
Cleaning the air fi lter
Remove the cleaner cover and the fi lter. Rinse it in warm soap suds.
Check that the fi lter is dry before reassembly. An air fi lter that has
been used for some time cannot be cleaned completely. Therefore,
it must regularly be replaced by a new one. A damaged fi lter must
always be replaced.
NOTE
Saturate the element in 2-cycle oil or the equivalent. Squeeze
the element to distribute the oil completely and to remove any
excess oil.
Spark plug (Fig. 11)
The spark plug condition is infl uenced by:
○ An incorrect carburetor setting.
○ Wrong fuel mixture (too much oil in the gasoline).
○ A dirty air fi lter.
○ Hard running conditions (such as cold weather).
These factors cause deposits on the spark plug electrodes, which
may result in malfunction and starting diffi culties. If the engine
is low on power, diffi cult to start or runs poorly at idling speed,
always check the spark plug fi rst. If the spark plug is dirty, clean it
and check the electrode gap. Readjust if necessary. The correct
gap is 0.6 mm. The spark plug should be replaced after about 100
operation hours or earlier if the electrodes are badly eroded.
NOTE
In some areas, local law requires using a resistor spark plug
to suppress ignition signals. If this machine was originally
equipped with resistor spark plug, use the same type of spark
plug for replacement.
000Book_TCH22EAP2(50ST)_WE_NE.indb 8000Book_TCH22EAP2(50ST)_WE_NE.indb 8 2013/04/04 18:13:152013/04/04 18:13:15
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi TCH22EBP2-62ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi TCH22EBP2-62ST in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info