661496
16
Zoom out
Zoom in
Previous page
1/288
Next page
English
16
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult
your dealer or the Tanaka dealer.
Condition Cause Remedy
Engine does not
start
Fuel
system
Fuel tank is empty or fuel level is low
Fill the fuel tank with the correct fuel mix
(25:1-50:1)
Fuel tank contains old fuel (o ensive odor)
Replace with new fuel
Too much fuel is absorbed and spark
plug is wet
1. Disconnect the spark plug and allow to dry
2. Pull the starter handle 5 or 6 times to
remove the surplus fuel
3. Attach the spark plug
4. Set the choke lever to RUN position and
pull the starter handle
Fuel lter is clogged with dirt Clean the fuel lter
Fuel pipe is bent or disconnected Ensure that the fuel ows smoothly
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Stop switch lead has short-circuited Contact Tanaka dealer
Spark plug is dirty Replace or clean the spark plug
Electrode gap is too big Adjust the gap to 0.6mm
Poor connection between high tension
cable and spark plug
Reconnect
Electrical system malfunction Contact Tanaka dealer
Other
Mu er exhaust port is clogged with
carbon
Contact Tanaka dealer for repair
Engine starts
but cuts out
straightaway
Engine is apt to
cut out
Fuel
system
Fuel tank is empty or fuel level is low
Fill the fuel tank with the correct fuel mix
(25:1-50:1)
Fuel tank contains old fuel (o ensive
odor)
Replace with new fuel
Two-cycle oil has not been added Contact Tanaka dealer
Choke lever is in START position Set the choke lever to RUN position
Air has got into fuel system Reconnect the fuel pipe or joint
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Ignition failure
Spark plug failure Replace with new spark plug
Electrical system failure Contact Tanaka dealer
Other
Engine overheating
Wrong spark plug model
Replace with designated part
See “SPECIFICATIONS”
Dirty air cleaner Clean
Carbon clogging (mu er exhaust port) Clean
Insu cient compression (piston, piston
ring, cylinder)
Contact Tanaka dealer
Abnormal vibration
Cutting attachment is not properly
installed
See “Installation of cutting attachment”
Handle, handle bracket or other
fastening part is loose
Check and tighten
Blade is bent or damaged Replace with new blade
Grass is wrapped round gear case Remove grass
Engine is running but blade
does not move
Movement is poor
Grass is wrapped round gear case Remove grass and dirt
000Book_TCG24ECP(S).indb 16000Book_TCG24ECP(S).indb 16 2017/03/24 10:10:482017/03/24 10:10:48
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi TCG27ECP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi TCG27ECP in the language / languages: All languages as an attachment in your email.

The manual is 45,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info