Manual Hitachi TCG27EBSPSL (page 12 of 88) (English, German, Dutch, French, Italian, Portuguese, Spanish)

571076

Zoom out

Zoom in

1/88

English

○ Blade thrust may occur when the spinning blade contacts a

solid object in the critical area.

A dangerous reaction may occur causing the entire unit and

operator to be thrust violently. This reaction is called blade

thrust. As a result, the operator may lose control of the unit

which may cause serious or fatal injury. Blade thrust is more

likely to occur in areas where it is diﬃ cult to see the material to

be cut.

○ Wear the harness as shown in the ﬁ gure (if so equipped). The

blade turns counter-clockwise, therefore, be advised to operate

the unit from right to left for eﬃ cient cutting. Keep onlookers out

of working area at least 15 m.

○ Use in accordance with local laws and regulations.

NOTE

Press the quick release button or pull emergency release ﬂ ap

(If so equipped) in the event of emergency. (Fig. 25)

WARNING

If cutting attachment should strike against stones or other

debris, stop the engine and make sure that the attachment and

related parts are undamaged. When grass or vines wrap around

attachment, stop engine and attachment and remove them.

Stopping (Fig. 27)

Decrease engine speed and run at an idle for a few minutes, then

turn oﬀ ignition switch (24).

WARNING

A cutting attachment can injure while it continues to spin after

the engine is stopped or power control is released. When the

unit is turned oﬀ , make sure the cutting attachment has stopped

before the unit is set down.

Semi-auto cutting head

○ When cutting, operate engine at over 6500 min

-1

. Extended

time of use at low rpm may wear out the clutch prematurely.

○ Cut grass from right to left.

WARNING

A cutting attachment can injure while it continues to spin after

the engine is stopped or power control is released. When the

unit is turned oﬀ , make sure the cutting attachment has stopped

before the unit is set down.

Automatically feeds more nylon cutting line when it is tapped at low

rpm (not greater than 4500 min

-1

MAINTENANCE

MAINTENANCE, REPLACEMENT OR REPAIR OF THE EMISSION

CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED

BY ANY NON-ROAD ENGINE REPAIR ESTABLISHMENT OR

INDIVIDUAL.

Carburetor adjustment (Fig. 28)

WARNING

○ The cutting attachment may be spinning during carburetor

adjustments.

○ Never start the engine without the complete clutch cover and

tube assembled! Otherwise the clutch can come loose and

cause personal injuries.

In the carburetor, fuel is mixed with air. When the engine is test

run at the factory, the carburetor is basically adjusted. A further

adjustment may be required, according to climate and altitude. The

carburetor has one adjustment possibility:

T = Idle speed adjustment screw.

OPERATING PROCEDURES

Fuel (Fig. 18)

WARNING

○ The trimmer is equipped with a two-stroke engine. Always run

the engine on fuel, which is mixed with oil.

Provide good ventilation, when fueling or handling fuel.

○ Fuel contains highly ﬂ ammable and it is possible to get the

serious personal injury when inhaling or spilling on your body.

Always pay attention when handling fuel. Always have good

ventilation when handling fuel inside building.

Fuel

○ Always use branded 89 octane unleaded gasoline.

○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1,

please consult the oil bottle for the ratio or Tanaka dealer.

○ If genuine oil is not available, use an anti-oxidant added quality

oil expressly labeled for air-cooled 2-cycle engine use (JASO

FC GRADE OIL or ISO EGC GRADE). Do not use BIA or TCW

(2-stroke water-cooling type) mixed oil.

○ Never use multi-grade oil (10 W/30) or waste oil.

○ Always mix fuel and oil in a separate clean container.

Always start by ﬁ ling half the amount of fuel, which is to be used.

Then add the whole amount of oil. Mix (shake) the fuel mixture. Add

the remaining amount of fuel.

Mix (shake) the fuel-mix thoroughly before ﬁ lling the fuel tank.

Fueling

WARNING

○ Always shut oﬀ the engine before refueling.

○ Slowly open the fuel tank, when ﬁ lling up with fuel, so that

possible over-pressure disappears.

○ Tighten the fuel cap carefully, after fueling.

○ Always move the trimmer at least 3 m from the fueling area

before starting.

○ Always wash any spilled fuel from clothing immediately with

soap.

○ Be sure to check for any fuel leakage after refueling.

Before fueling, clean the tank cap area carefully, to ensure that

no dirt falls into the tank. Make sure that the fuel is well mixed by

shaking the container, before fueling.

Starting

CAUTION

Before starting, make sure the cutting attachment does not

touch anything.

1. Set ignition switch (24) to forward away from stop position.

(Fig. 19)

* Push priming bulb (25) several times so that fuel ﬂ ows through

return pipe (26). (Fig. 20)

2. Set choke lever (27) to START position (closed) (A) (Fig. 21)

3. Pull recoil starter briskly, taking care to keep the handle in your

grasp and not allowing it to snap back. (Fig. 22)

4. When you hear the engine want to start, return choke lever to

RUN position (open) (B). Then pull recoil starter briskly again.

NOTE

If engine does not start, repeat procedures from 2 to 4.

5. Then allow the engine about 2–3 minutes to warm up before

subjecting it to any load.

6. Check that the cutting attachment does not rotate when the

engine is idling.

Cutting (Fig. 23 – 26)

○ When cutting, operate engine at over 6500 min

-1

. Extended

time of use at low rpm may wear out the clutch prematurely.

○ Cut grass from right to left.

000Book_TCG24EBSP_WE.indb 12000Book_TCG24EBSP_WE.indb 12 2014/03/26 14:05:132014/03/26 14:05:13

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi TCG27EBSPSL in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 10,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi TCG27EBSPSL Manual

Product: