571077
15
Zoom out
Zoom in
Previous page
1/88
Next page
15
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not operate
normally. If this does not remedy the problem, consult your dealer
or the Tanaka dealer.
Condition Cause Remedy
Engine does not start
Fuel system
Fuel tank is empty or fuel level is low Fill the fuel tank with the correct fuel mix (25:1-50:1)
Fuel tank contains old fuel (offensive odor) Replace with new fuel
Too much fuel is absorbed and spark plug is
wet
1. Disconnect the spark plug and allow to dry
2. Pull the starter handle 5 or 6 times to remove the
surplus fuel
3. Attach the spark plug
4. Set the choke lever to RUN position and pull the
starter handle
Fuel lter is clogged with dirt Clean the fuel lter
Fuel pipe is bent or disconnected Ensure that the fuel ows smoothly
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Stop switch lead has short-circuited Contact Tanaka dealer
Spark plug is dirty Replace or clean the spark plug
Electrode gap is too big Adjust the gap to 0.6mm
Poor connection between high tension cable
and spark plug
Reconnect
Electrical system malfunction Contact Tanaka dealer
Other Muf er exhaust port is clogged with carbon Contact Tanaka dealer for repair
Engine starts but cuts
out straightaway
Engine is apt to cut
out
Fuel system
Fuel tank is empty or fuel level is low Fill the fuel tank with the correct fuel mix (25:1-50:1)
Fuel tank contains old fuel (offensive odor) Replace with new fuel
Two-cycle oil has not been added Contact Tanaka dealer
Choke lever is in START position Set the choke lever to RUN position
Air has got into fuel system Reconnect the fuel pipe or joint
Carburetor malfunction Contact Tanaka dealer
Electrical
system
Ignition failure
Spark plug failure Replace with new spark plug
Electrical system failure Contact Tanaka dealer
Other
Engine overheating
Wrong spark plug model
Replace with designated part
See “SPECIFICATIONS”
Dirty air cleaner Clean
Carbon clogging (muf er exhaust port) Clean
Insuf cient compression (piston, piston ring,
cylinder)
Contact Tanaka dealer
Abnormal vibration
Cutting attachment is not properly installed See “Installation of cutting attachment”
Handle, handle bracket or other fastening part
is loose
Check and tighten
Blade is bent or damaged Replace with new blade
Grass is wrapped round gear case Remove grass
Engine is running but blade does not
move
Movement is poor
Grass is wrapped round gear case Remove grass and dirt
Engine does not stop Stop switch failure
Set the choke lever to START position to stop the
engine
Cease use immediately and contact Tanaka dealer
Engine stops when throttle is closed Idle speed is too low Contact Tanaka dealer
Blade continues rotating when throttle
is closed
Idle speed is too high
Throttle wire is too taut
Contact Tanaka dealer
000Book_TCG24EBSP_WE.indb 15000Book_TCG24EBSP_WE.indb 15 2014/03/26 14:05:132014/03/26 14:05:13
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi TCG27EBSPS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi TCG27EBSPS in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 10,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info