512001
5
Zoom out
Zoom in
Previous page
1/22
Next page
3
English
Voltage (by areas)*
Power Input*
No-load speed
Weight (without cord)
1. Mounting
(1) Attach the washer nut on the rubber pad.
(2) While pushing the lock lever with one hand, lock
the spindle by turning the rubber pad slowly with
the other hand.
Tighten the washer nut by using the supplied
wrench.
(3) Cover the rubber pad with the wool bonnet.
Pull the string of the wool bonnet, let it connect
the rubber pad, and tie the string up. Then, tuck
the knot and the remainder of the string into the
wool bonnet. (See Fig. 2)
CAUTION:
Improper fitting of the wool bonnet may cause
vibration.
Confirm that the lock lever is disengaged by pushing
lock lever two or three times before switching the
polisher on.
2. Dismounting
To remove the wool bonnet, follow the above
precedures in reverse.
PRACTICAL POLISHER APPLICATION
1. Curved surface as well as plain one is treated for
finishing. It is recommended to hold the polisher
without pushing on the material, and make the best
of the weight of the machine alone. As the excessive
pressure on the polishing surface will not only bring
unsatisfactory result but also apply overload on the
motor.
2. Depending on the finishing degree of the surface,
use the polishing compound or wax. In order to
attain the maximum polishing effect, first polish the
surface with the fine sand paper using the sander,
than polish it with the polishing compound using
the wool bonnet, and than finish with wax. Apply
a small quantity of the compound and wax to the
surface, and polish with the wool bonnet.
3. Don’t let the cord touch the wool bonnet during
its operation, for the rotating wool bonnet may
catch the cord and get caught it in.
4. Switching on the polisher
Pulling the trigger of switch and push the stopper,
it keeps the switched-on condition and it is
convenient for the continuous operation. When
switched off, the stopper can be disengaged by
means of pulling the trigger again.
5. Precaution after use
Do not lay the polisher down immediately after
using on a place where there are many shavings,
much dirt and dust until it has completely stopped
revolving.
SPECIFICATIONS
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
650 W
2000/min
2.9 kg
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) 180mm Wool Bonnet ................................................. 1
(2) Rubber Pad ................................................................. 1
(3) Wrench ........................................................................ 1
(4) Side handle ................................................................. 1
Standard accessories are subject to change without
notice.
APPLICATIONS
Polishing or shining painted metal surfaces, such
as those of automobiles, trains, elevators,
refrigerators, sewing machines, washing machines,
metal appliances, etc.
Polishing varnished surfaces of wooden furniture,
etc.
Shining synthetic resin or ebonite products.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
Caution:
Damaged cord must be replaced or repaired.
4. Fixing the side handle
Screw the side handle into the housing.
5. Confirm the lock lever.
Confirm that the lock lever is disengaged by pushing
lock lever two or three times before switching the
power tool on (See Fig. 1).
MOUNTING AND DISMOUNTING THE WOOL
BONNET (Fig. 1)
CAUTION: Be sure to switch OFF and disconnect the
attachment plug from the receptacle to avoid
a serious accident.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi SP18SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi SP18SA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi SP18SA

Hitachi SP18SA Additional guide - English, German, Dutch, French, Italian, Portuguese, Spanish - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info