78495

Hitachi SP 18 VA Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
6
English
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency
to snag the rotating accessory and cause loss of
control or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
SAFETY WARNINGS SPECIFIC FOR SANDING
OPERATIONS
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when
selecting sanding paper.
Larger sanding paper extending beyond the sanding
pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
SAFETY WARNINGS SPECIFIC FOR
POLISHING OPERATIONS
a) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
PRECAUTIONS ON USING ELECTRONIC
SANDER POLISHER
1. Never mount a grinding wheel and attempt to use
this tool as a disc grinder.
2. Always hold the body handle and side handle of
the power tool firmly.
Otherwise the counterforce produced may result in
inaccurate and even dangerous operation.
3. Ensure that sparks resulting from use do not create
a hazard e. g. do not hit persons, or ignite flammable
substances.
4. Always use protective safety glasses and hearing
protectors, use other personal protective equipment
such as gloves, apron and helmet when necessary.
5. Always use eye and ear protection.
Other personal protective equipment such as dust
mask, gloves, helmet and apron should be worn
when necessary.
If in doubt, wear the protective equipment.
SPECIFICATIONS
Voltage (by areas)* (110V, 120V, 220V, 230V, 240V)
Power input 1250 W*
No load speed 0 – 3400 min
-1
Sanding Disc Size outer dia. × inner dia. 180 × 22 mm
Weight (without cord, standard accessories) 2.8 kg
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Rubber Pad ................................................................ 1
(2) Loop Handle (with bolt and washer) ................... 1
(3) Bar Wrench ................................................................ 1
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜ Grinding metal surfaces
⅜ Preliminary sanding of metal surfaces before
painting, rust removal, removing old paint before
repainting.
⅜ Finishing woodwork, correcting projections of timber
from joints or assemblies.
⅜ Preliminary sanding of wood surfaces before
applying paint.
⅜ Polishing or shining painted metal surfaces, such
as those of automobiles, trains, elevators,
refrigerators, sewing machines, washing machines,
metal appliances, etc.
⅜ Polishing varnished surfaces of wooden furniture,
etc.
⅜ Shining synthetic resin or ebonite products.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
CAUTION
Do not operate on Direct Current power source.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
01Eng_SP18VA_WE 2/19/09, 19:426
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi SP 18 VA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi SP 18 VA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi SP 18 VA

Hitachi SP 18 VA Additional guide - English, German, Dutch, French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info