79236

Hitachi SB 10V2 Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
5
English
BELT SANDER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, because
the belt may contact its own cord. Cutting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
CAUTION
Prior to the sanding operation, make sure the
material you are going to sand.
If generation of harmful/ toxic dusts such as lead
paint, woods and metals is expected under the
sanding operation, make sure the dust bag or
appropriate dust extraction system is connected
with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts
generated in sanding operation, the dust can
endanger the health of yourself and bystanders.
STANDARD ACCESSORIES
(1) Endless sanding belt (Grain size: #80) ................ 1
(2) Dust bag .................................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES
(sold separately)
1. Endless sanding belts
Table1
Grain size Grain Type
40 AA, WA, CC
60 AA, WA, CC
80 AA, WA, CC
100 AA, WA, CC
120 AA, WA, CC
150 AA, WA, CC
180 AA, WA, CC
240 AA, WA, CC
NOTE:
The endless sanding belt is sold in package of 10
belts of the same type. When ordering, specify the
grain type and grain size desired.
2. Stationary Stand
When sanding small articles, use a stationary stand
for convenience.
Optional accessories are subject to change without notice.
APPLICATIONS
⅜ Finish sanding and finish flooring of woodwork
products.
SPECIFICATIONS
Model SB10V2 SB10S2
Voltage (by areas)* (110 V, 120 V, 127 V, 220 V, 230 V, 240 V)
Power input* 1020 W
No–load belt speed 240 – 420 m /min 420 m /min
Sanding belt size 100 × 610 mm
Weight (without cord) 5.2 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
⅜ Base polishing of wood-coated surfaces.
⅜ Finish sanding of metal surfaces.
⅜ Base polishing of metal-coated surfaces, rust
removal, or paint removal prior to refinishing.
⅜ Surface finishing of slate, concrete, and similar
materials.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
an rated capacity. The extension cord should be
kept as short as practicable.
4. Attach the sanding belt
For details, refer to the section on “Sanding Belt
Assembly”.
5. RCD
The use of a residual current device with a rated
residual current of 30mA or less at all times is
recommended.
HOW TO HANDLE SANDING BELT
CAUTION:
Be sure to switch power OFF and disconnect the
plug from the receptacle to avoid serious trouble.
01Eng_SB10V2_WE 2/23/12, 3:50 PM5
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi SB 10V2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi SB 10V2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info