Manual Hitachi SAY150A (page 6 of 32) (English, German, Dutch, French, Italian, Spanish)

570719

Zoom out

Zoom in

1/32

English

*Be sure to check the nameplate on product as it is subject to change by areas.

SPECIFICATIONS

Voltage (by areas)* (110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)

Power Input 380 W*

No-load speed 6000 min

–1

Disc size 150 mm

Weight (without cord, standard accessories)

2.1 kg

STANDARD ACCESSORIES

(1) Sanding Pad ................................................................ 1

(2) Sanding Paper (#120 without hole) .......................... 1

(3) Bar Wrench ................................................................. 1

(4) Side handle ................................................................. 1

(5) Hexagon Bar Wrench ................................................. 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

(1) Dust Collection Set

(2) Dust hose (1.5m)

(3) Sanding Paper (with hole&without hole)

(4) Sanding Paper Punch

Optional accessories are subject to change without notice.

APPLICATIONS

Finishing of reparative coating of automobiles, painted

metal plates, etc.

ࠗ Bordering between painted surfaces and metal

surfaces.

ࠗ Polishing polyester patties.

Erasing letters, figures., etc., in reparative coating of

billboards.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF positon. If

the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Attaching sanding paper:

(1) As shown in Fig. 1, peel off the lining paper beginning

at the slit part. Ensure t hat the adhesive on the back

of the sanding paper does not become fouled with

dust or other foreign matter.

(2) After ensuring that the sanding pad is free of dust

and oil, mount the sanding paper to the sanding pad

as shown in Fig. 2, ensuring that the outer

circumferences of the pad and paper are matched.

(3) Ensure that the sanding paper is securely attached to

the pad by pressing the paper strongly with the palm

of the hand, as shown in Fig. 3.

CAUTION

If the sanding paper is not attached securely as

described above, it could come off during operation,

inviting serious injury. As the adhesive may

deteriorate if the sanding paper is removed and

reattached several times, the sanding paper should

be aligned and attached securely in a single operation.

PRACTICAL OPERATING PROCEDURES

1. Turn the sander on after lightly applying it to the

surface to be sanded. Never leave the rotating tool

unattended.

2. Do not apply excessive pressure to the sander.

Excessive pressure may result in deterioration of the

sanded surface, and overloading of the tool.

3. Hold the housing and side handle of the sander

securely during operation .

4. The sanding paper should be removed as soon as

possible after completion of the operation. Sanding

paper left on the pad for several days may be very

difficult to remove.

5. After removing the sanding paper, ensure that any

adhesive remaining on the sanding pad is removed

completely by wiping it. Should any adhesive remain,

dust and dirt will adhere to the pad, resulting in

reduced adhesion when another sanding paper is

mounted.

6. Do not attemp to reattach sanding paper to the pad

once it has been removed. Reduced adhesive strength

could cause the sanding paper to come flying off the

pad, creating a serious hazard.

CAUTION

Inmediately after use, DO NOT lay the tool down or

touch the sanding pad until the rotating parts of the

tool come to a complete stop. Laying the tool down

in this manner could cause grit and dirt to be sucked

into the tool. Touching the rotating sanding paper

could cause serious injury.

PRECAUTIONS ON USING ORBITAL

1. Never mount a grinding wheel and attempt to use

this tool as a disc grinder.

2. Ensure the sanding paper is securely attached by

pressing firmly.

3. Never apply grinding fluid or water to the unit or

material during operation.

4. Always hold the body handle and side handle of the

power tool firmly .

Otherwise the counterforce produced may result in

inaccurate and even dangerous operation.

01Eng_SAY-150A_WE 4/21/14, 2:50 PM5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi SAY150A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi SAY150A Manual

Product: