Manual Hitachi S18SB (page 5 of 41) (English, German, Dutch, French, Italian, Portuguese, Spanish)

512000

Zoom out

Zoom in

1/41

English

CAUTION:

Damaged cord must be replaced or repaired.

4. Attaching sanding disc

For attachment/removal of the sanding disc, refer

to “ATTACHMENT/REMOVAL OF SANDING DISC”.

Many types of sanding discs are available; select

one appropriate to the work.

5. Fixing the side handle

Screw the side handle into the housing.

6. Confirm the lock lever.

Confirm that the lock lever is disengaged by pushing

lock lever two or three times before switching the

power tool on (See Fig. 2).

7. Install the air cover on the air vent on the side

where the side handle is attached to divert the

cooling air flow of the motor during operation as

much as possible. Hook tab of the air cover to the

air vent and push in the tab when installing. Use

a screwdriver etc. to pull as shown in Fig. 3 when

removing.

CAUTION

Prior to the sanding operation, make sure the

material you are going to sand.

If generation of harmful/toxic dusts such as lead

paint, woods and metals is expected under the

sanding operation, make sure the dust bag or

appropriate dust extraction system is connected

with dust outlet tightly.

Wear the dust mask additionally, if available.

Do not inhale or touch the harmful/toxic dusts

generated in sanding operation, the dust can

endanger the health of yourself and bystanders.

PRACTICAL SANDER APPLICATION

1. Do not heavily push the sanding disc to the surface

to be ground. Grinding operation can be achieved

with the weight of the machine alone, so maintain

the sanding disc to an extent that it lightly touches

the surface to be ground. When the sanding disc

is pushed heavily, its revolving speed drops, creating

an unevenly finished surface and causing motor

seizure from overload.

2. Rather than applying the entire disc surface to the

metal surface to be ground, use the sander by

inclining it approximately 15°~30° to grind with the

disc peripheral portion. (Fig. 1)

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) 180mm Sanding Disc (Grain size: P50 or P16) ......... 1

(2) Rubber Pad ................................................................. 1

(3) Wrench ........................................................................ 1

(4) Side handle ................................................................. 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES (sold separately)

(1) 180mm Sanding disc

⅜ There are eleven different kinds of sanding disc,

having grain sizes of P16, P20, P24, P30, P36, P40,

P50, P60, P80, P100, P120. When placing your order,

please specify the grain size of the disc desired.

Optional accessories are subject to change without notice.

APPLICATIONS

⅜ Sanding metal surfaces.

⅜ Preliminary sanding of metal surfaces before

painting, rust removal, removing old paint before

repainting.

⅜ Finishing woodwork, correcting projections of

timbers from joints or assemblies.

⅜ Preliminary sanding of wood surfaces before

applying paint.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

Voltage (by areas)*

Power Input*

No-load speed

Weight (only main body)

PRECAUTIONS ON USING DISC SANDER

1. Keep away from a revolving sanding disc.

2. Pay strict attention to sparks.

3. Hold the disc sander firmly.

4. Do not leave the revolving disc sander unattended

on the floor.

5. Be careful those around one while operating.

6. Follow the procedures of these handling

instructions on sanding disc replacement.

7. Never mount a depressed center wheel on this

tool and attempt to use it as a disc grinder.

(110V, 115V, 120V, 127V, 220V, 230V, 240V)

705 W

4500 min

–1

2.0 kg

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi S18SB in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,54 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi S18SB Manual

Product: