570706

Hitachi RH600T Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
6
English
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach
of children and infi rm persons.
HEAT GUN SAFETY WARNINGS
WARNING
1. This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety.
2. Children should be supervised to ensure that they do
not play with the tool.
3. A fi re may arise if the tool is not used with care, therefore:
Be careful when using the tool in places where there are
combustible materials.
Do not apply to the same place for a long time.
Do not use in presence of an explosive atmosphere.
Be aware that heat may be conducted to combustible
materials which are out of sight.
Place on its stand after use and follow to cool before
storage.
Do not leave the tool unattended when in use.
4. Do not use the tool or touch the power plug with wet
hands.
Failure to observe this may result in electric shocks.
5. Always check the work area prior to use, and do not use
the tool if safety cannot be guaranteed.
Failure to observe this may result in infl ammable
articles concealed in or behind invisible areas (cases,
ceilings, fl oors, hollow areas) being ignited.
6. Do not stand underneath when using the tool in elevated
locations.
Also, do not catch the power cord on anything, or allow
it to be pulled.
Failure to observe this may result in accidents.
7. Do not point the hot wind directly at people or animals.
Do not look into the nozzle. Do not use it as a hair dryer
under any circumstances.
Failure to observe this may result in accidents or injury.
8. There are cases in which highly toxic gas will be emitted
if used on plastic, lacquer or similar materials.
Always ensure that the work area is fully ventilated, and
wear a dust-protection mask.
9. Apply heat gently while moving the Heat Gun up, down,
left and right.
Aiming it constantly at a single location may result in the
outbreak of smoke or fi re.
10. Check the tool for damage, cracks or malformation in
the event of it being accidently dropped or subject to
impact.
Damage, cracks and malformation may result in injury.
11. Cease operations immediately in the event of the
tool not operating properly or if abnormal noises or
vibrations are noticed, and contact a Hitachi Authorized
Service Center to request inspections and repairs.
Continued use may result in injury.
12. Do not get away from the unit while it is switched on.
Failure to observe this may result in accidents.
13. If during use, electricity is interrupted, (e.g. the power
plug came out, the breaker fell, a blackout occurred…)
and the heat gun fan has stopped, please put the switch
in OFF position. If the switch is left in ON position when
power resumes, the restart of the fan may cause fi re.
CAUTION
1. Parts of the nozzle supplied are sharp, so use gloves
when removing them from the case and when attaching
or detaching them.
2. The hot wind release nozzle, the tip of the nozzle and
the material that was heated are extremely hot during
and immediately after using the tool, so use gloves and
avoid touching them directly.
3. Do not use inside boxes, drawers or other enclosed
spaces.
Aiming it constantly at a single location may result in the
outbreak of smoke or fi re.
4. Make sure the nozzle is at least 5cm away from the item
being heated when using the tool. Also, do not cover or
otherwise block the nozzle.
Failure to observe this may result in the Heat Gun
overheating, leading to malfunctions.
5. Do not switch the tool on and off repeatedly. Also, do not
use the tool with the power cord folded or twisted.
Failure to observe this may result in malfunctions.
6. Do not point the heat-wind release nozzle downwards
immediately after use.
Failure to observe this may result in the tool overheating,
leading to malfunctions.
SPECIFICATIONS
Power supply
Type Can be used with both 50 Hz and 60 Hz single-phase current.
Voltage 110 V 120 V to 127 V 220 V to 240 V
Rated electrical
current
12.9 A 12.2 A 8.8 A
Power Input 1375 W 1500 W 2000 W
Capacity
Wind volume 0.25 m
3
/min to 0.5 m
3
/min (2-stage switch)
Wind temperature
250 – 500°C
2-stage switch
50°C
(When the cooling button is used.)
350 – 500°C
2-stage switch
50°C
(When the cooling button is used.)
450 – 600°C
2-stage switch
50°C
(When the cooling button is used.)
Motor type Direct current motor
Weight 0.57 Kg
000Book_RH600T_WE.indb 6000Book_RH600T_WE.indb 6 2013/10/04 13:41:552013/10/04 13:41:55
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi RH600T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi RH600T in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info