214485
75
Zoom out
Zoom in
Previous page
1/82
Next page
64
Phenomenon Cases not involving a machine defect
Troubleshooting
Phenomena that may be easily mistaken as machine defects
Before requesting repair, please check the following chart. This will sometimes
provide a solution to your problem.
If a situation cannot be resolved, the projectors microprocessor may need to be
reset, or settings may be incorrect.
To reset the microprocessor, turn the projector off
once, and turn it on again (20). If the projector
cannot be turned off, use the restart switch.
Pressing the restart switch using a pin or similar
object will restart the projector (7, 23).
To reset all settings to the factory default, please
use the FACTORY RESET item in the SERVICE
menu which is in the OPTION menu (55).
If the problem is not solved after performing maintenance, please contact your
dealer or service company.
► Never use the projector if there is any abnormality such as
smoke, strange odor, excessive noise, damaged casing, elements or cables,
penetration of liquids or foreign matter, etc. In such cases, immediately turn
the power off and then disconnect the power plug from the power outlet. After
making sure that the smoke or odor has stopped, contact your dealer or service
company.
WARNING
Power does not
come on.
No pictures are
output
The electrical power cord is not plugged in.
Correctly connect the power cord (17).
The power switch is not set to the on position.
Set the power switch to [ | ] (On position) (20).
The main power source has been interrupted during operation
by a power outage (blackout), etc.
Please turn the power off (
23), and allow the projector to cool
down for at least 20 minutes.
After the projector has cooled down sufficiently, please turn the
power on again (20).
Either the lamp or lamp cover has not been properly fastened.
Please turn the power off (
23), and allow the projector to cool
down for at least 45 minutes.
After the projector has sufficiently cooled down, confirm that the
lamp and lamp cover are properly fastened (58). Then turn the
power on again (20).
The lens cover is closed.
Remove the lens cover (6).
The signal cables are not correctly connected.
Correctly connect the connection cables (13-16).
(Continued on next page)
Y
C
B
/P
B
CR/PR
COMPONENT VIDEO
S-VIDEO
VIDEO
COMPUTER
CONTROL
HDMI
TRIGGER
AC IN
I O
Restart switch
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi pj tx200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi pj tx200 in the language / languages: English as an attachment in your email.

The manual is 8,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info