Manual Hitachi P20SE (page 7 of 34) (English, German, Dutch, French, Italian, Spanish)

568920

Zoom out

Zoom in

1/34

English

STANDARD ACCESSORIES

1. Box Wrench (for securing cutter blade) ............. 1

2. Set Gauge (for adjusting cutter height) .............. 1

3. Guide (with set screw) ........................................... 1

4. Blade Sharpening Ass'y

(for Resharpenable Blade Type) .......................... 1

Standard accessories are subject to change without no-

tice.

OPTIONAL ACCESSORIES (sold separately)

1. Dust collection adapter

Optional accessories are subject to change without no-

tice.

APPLICATIONS

⅜ Planing various wooden planks and panels.

(See Fig. 1-4)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized con-

forms to the power requirements specified on the

product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Prepare a stable wooden workbench suitable for

planing operation. As a poorly balanced workbench

creates a hazard, ensure it is securely positioned

on firm, level ground.

PLANING PROCEDURES

1. Adjusting the cutter depth:

(1) Turn the knob in the direction indicated by the

arrow in Fig. 5 (clockwise), until the triangular mark

is aligned with the desired cutting depth on the

scale. The scale unit is graduated in millimeters.

(2) The cutting depth can be adjusted within a range

of 0-1mm.

2. Surface cutting

Rough cutting should be accomplished at large

cutting depths and at a suitable speed so that

shavings are smoothly ejected from the machine.

To ensure a smoothly finished surface, finish cut-

ting should be accomplished at small cutting depths

and at low feeding speed.

3. Beginning and ending the cutting operation:

As shown in Fig. 6, place the front base of the

planer on the material and support the planer

horizontally. Turn ON the power switch, and slowly

operate the planer toward the leading edge of the

material. Firmly depress the front half of the planer

at the first stage of cutting, as shown in Fig. 7,

depress the rear half of the planer at the end of

the cutting operation. The planer must always be

kept flat throughout the entire cutting operation.

4. Precaution after finishing the planing operation:

When the planer is suspended with one hand after

finishing the planing operation, ensure that the

cutting blades (base) of the planer do not contact

or come too near your body. Failure to do so could

result in serious injury.

CARBIDE BLADE ASSEMBLY AND DISAS-

SEMBLY AND ADJUSTMENT OF CUTTER

BLADE HEIGHT (FOR DOUBLE EDGED BLADE

TYPE)

1. Carbide blade disassembly:

(1) As shown in Fig 8, loosen the blade holder with

the attached box wrench.

(2) As shown in Fig 9, remove the carbide blade by

sliding it with the attached box wrench.

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power Input 570W*

Cutting Width 82mm

Max. Cutting Depth 1mm

Weight (without cord and guide) 2.5kg

No-Load Speed 15000/min

* Be sure to check the nameplate on product as it is subject to change by areas.

PRECAUTIONS ON USING PLANER

⅜ Do not use the Planer with the blades facing upward

(as stationary type planer).

SPECIFICATIONS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi P20SE in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi P20SE Manual

Product: