Manual Hitachi P20SB (page 8 of 52) (English, German, Dutch, French, Italian, Portuguese, Spanish)

568919

Zoom out

Zoom in

1/52

English

STANDARD ACCESSORIES

1. Box Wrench (for securing cutter blade) ............. 1

2. Set Gauge (for adjusting cutter height) .............. 1

3. Guide (with set screw) ........................................... 1

4. Blade Sharpening Ass'y .......................................... 1

Standard accessories are subject to change without notice.

APPLICATIONS

⅜ Planing various wooden planks and panels.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)

Power Input 570W*

Cutting Width 82mm

Max. Cutting Depth 1mm

Weight (without cord) 2.5kg

No-Load Speed 15000 min

-1

* Be sure to check the nameplate on product as it is subject to change by areas.

PLANER SAFETY RULES

1. Wait for the cutter to stop before setting the tool

down.

An exposed cutter may engage the surface leading

to possible loss of control and serious injury.

2. Do not use the Planer with the blades facing upward

(as stationary type planer).

3. Use dust collection adapter if need to reduce dust

related hazards.

(1) Unscrew the left side screw on bearing cover

(Item no. 23 show in assembly drawing) on

housing.

(2) Mount dust collection adapter on housing with

screws.

Dust collection adapter (Code no. 313928)

(3) Connect the dust extraction and collection

facilities with the tube of dust collection adapter

firmly.

(4) Wear dust mask additionally, if available.

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Prepare a stable wooden workbench suitable for

planing operation. As a poorly balanced workbench

creates a hazard, ensure it is securely positioned

on firm, level ground.

PLANING PROCEDURES

1. Adjusting the cutter depth:

(1) Turn the knob in the direction indicated by the

arrow in Fig. 1 (clockwise), until the triangular mark

is aligned with the desired cutting depth on the

scale. The scale unit is graduated in millimeters.

(2) The cutting depth can be adjusted within a range

of 0-1mm.

2. Surface cutting:

Rough cutting should be accomplished at large

cutting depths and at a suitable speed so that

shavings are smoothly ejected from the machine.

To ensure a smoothly finished surface, finish cutting

should be accomplished at small cutting depths and

at low feeding speed.

3. Beginning and ending the cutting operation:

As shown in Fig. 2, place the front base of the

planer on the material and support the planer

horizontally. Turn ON the power switch, and slowly

operate the planer toward the leading edge of the

material. Firmly depress the front half of the planer

at the first stage of cutting, as shown in Fig. 3,

depress the rear half of the planer at the end of

the cutting operation. The planer must always be

kept flat throughout the entire cutting operation.

4. Precaution after finishing the planing operation:

When the planer is suspended with one hand after

finishing the planing operation, ensure that the

cutting blades (base) of the planer do not contact

or come too near your body. Failure to do so could

result in serious injury.

Planing

Beveling

Rabbeting

Max. 12mm

Max. 6mm

SPECIFICATIONS

01Eng_P20SB_WE_8L 08/12/19, 21:267

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi P20SB in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi P20SB Manual

Product: