568917

Hitachi P20DA Manual

10
Zoom out
Zoom in
Previous page
1/38
Next page
English
9
(2) Place the blade holder on the completed assembly,
as shown in Fig. 25, and fasten it with the three
bolts. Ensure that the bolts are securely tightened.
(3) Turn the cutter block over, and set the opposite side
in the same manner.
3. Adjustment of blade height:
(1) Loosen the 2 screws holding on the blade and set
plate (A).
(2) Press the turned surface of set plate (A) to the wall
surface
b
while adjusting the blade edge to the wall
surface
a
of the set gauge. Then, tighten them with
the 2 screws. (Fig. 18, 26)
SHARPENING THE RESHARPENABLE BLADES
Use of the accessory Blade Sharpening Ass'y is recom-
mended for convenience.
1. Use of Blade Sharpening Ass'y
As shown in Fig. 27, two blades can be mounted
on the blade sharpening ass'y to ensure that the
blade tips are ground at uniform angles. During
grinding, adjust the position of the blades so that
their edges simultaneously contact the dressing
stone as shown in Fig. 28.
2. Blade sharpening intervals
Blade sharpening intervals depend on the type of
wood being cut and the cutting depth. However,
sharpening should generally be effected after each
500 meters of cutting operation.
3. Dressing Stone
When a water dressing stone is available, use it
after dipping it sufficiently in water since such a
dressing stone may be worn during grinding works,
flatten the upper surface of the dressing stone as
often as necessary.
MAINTENANCE AND INSPECTION
1. Inspecting the blades:
Continued use of dull or damaged blades will result
in reduced cutting efficiency and may cause over-
loading of the motor. Sharpen or replace the blades
as often as necessary.
2. Handling
CAUTION
⅜ The front base, rear base, and cutting depth control
knob are precisely machined to obtain specifically
high precision. If these parts are roughly handled
or subjected to heavy mechanical impact, it may
cause deteriorated precision and reduced cutting
performance. These parts must be handled with
particular care.
3. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Fail-
ure to do so could result in serious hazard.
4. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
5. Cleaning on the outside
When the planer is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner,
for they melt plastics.
6. Storage
Store the planer in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance
with the following code:
Blue: -- Neutral
Brown: -- Live
As the colours of the wires in the main lead of this tool
may not correspond with the coloured markings identify-
ing the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black.
The wire coloured brown must be connected to the
terminal marked with the letter L or coloured red.
Neither core must be connected to the earth terminal.
NOTE
This requirement is provided according to BRITISH STAN-
DARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to
EN50144.
The typical A-weighted sound pressure level: 88dB (A).
The typical A-weighted sound power level: 101dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value does not exceed 2.5m/s
2
.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi P20DA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi P20DA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info