568916

Hitachi NV90AG Manual

8
Zoom out
Zoom in
Previous page
1/48
Next page
8
English
(including yourself). Even when no nails are loaded
at all, it is dangerous to discharge the tool while
pointing it at someone, so never attempt to do so.
No horseplay. Respect the tool as a working
implement.
9. Before using the power tool, check the push lever.
Before using the power tool make sure to check
that the push lever and valve operate properly.
Without nails loaded into the power tool, connect
the hose and check the following. If the sound of
operation occurs this indicates a fault, so in such a
case do not use the power tool until it has been
inspected and repaired.
⅜ If merely pulling the trigger causes operating
sound of driver blade movement occur, the
power tool is faulty.
⅜ If merely pushing the push lever against the
material to be nailed causes the sound of driver
blade movement to occur, the power tool is
faulty. Furthermore, with regard to the push
lever, please note that it must never be modified
or removed.
10. Use specified nails only.
Never use nails other than those specified and
described in these instructions.
11. Be careful when connecting the hose.
When connecting the hose and loading nails in
order not to fire the tool by mistake, make sure of
the following.
⅜ Do not touch the trigger.
⅜ Do not allow the firing head to contact with any
surface.
⅜ Keep the firing head down.
Strictly observe the above instructions, and
always make sure that no part of the body,
hands or legs is ever in front of the nail outlet.
12. Do not carelessly place your finger on the trigger.
Do not place your finger on the trigger except when
actually nailing. If you carry this tool or hand it to
someone while having your finger on the trigger,
you may inadvertently discharge a nail and thus
cause an accident.
13. Completely Close the nail guide and do not open it
during operation.
If nailing is attempted when the nail guide is open,
nails will not be driven into the timber, and there is
a risk of dangerous discharge.
14. Press the nail outlet firmly against the material to
be nailed.
When driving in nails, press the nail outlet firmly
against the material to be nailed. If the outlet is not
applied properly, the nails may rebound.
15. Keep hands and feet away from the firing head
when using.
It is very dangerous for a nail to hit the hands or
feet by mistake.
16. Beware of the tool’s kickback
Do not approach the top of the tool with your head
etc. during operation. This is dangerous because
the tool may recoil violently if the nail currently
being driven in comes into contact with a previous
nail or a knot in the wood.
17. Take care when nailing thin boards or the corners
of wood.
When nailing thin boards, the nails may pass right
through, as may also be the case when nailing the
corners of wood due to deviation of the nails. In
such cases, always make sure that there is no one
(and nobody’s hands or feet; etc.) behind the thin
board or next to the wood you are going to nail.
18. Simultaneous nailing on both sides of the same
wall is dangerous
Under no circumstances should nailing be
performed on both sides of a wall at the same time.
This would be very dangerous since the nails might
pass through the wall and thus cause injuries.
19. Do not use the power tool on scaffoldings, ladders.
The power tool shall not be used for specific
application for example:
– when changing one driving location to another
involves the use of scafforldings, stairs, ladders
or ladder alike constructions, e.g. roof laths,
– closing boxes or crates,
– fitting transportation safety systems e.g. on
vehicles and wagons
20. Do not disconnect the hose with your finger on the
trigger.
If you disconnect the hose with your finger on the
trigger, the next time the hose is connected, there
is a danger that the power tool will fire a nail
spontaneously, or operate incorrectly.
21. Disconnect the hose and take out any nails left in
the magazine after use.
Disconnect tool from air before doing tool
maintenance, cleaning a jammed fastener, leaving
work area, moving tool to another location, or after
use. It is very dangerous for a nail to be fired by
mistake.
22. When removing a nail which has become stuck,
make sure to first of all disconnect the hose and
release compressed air.
When removing a nail which has become stuck in
the nail outlet, first of all make sure to disconnect
the hose and release compressed air inside the
power tool.
Accidental firing of the nail could be very dangerous.
23. To avoid hazards caused by falling nails, never
open the magazine with the device facing
downward while loading nails.
24. A female plug (air socket) should not be used in the
body.
If a female plug is installed in the body, the
compressed air sometimes can not be drawn when
the hose is disconnected so avoid this.
The tool and air supply hose must have a hose
coupling such that all pressure is removed from the
tool when the coupling joint is disconnected.
25. When attaching and detaching the nose cap,
disconnect the hose.
When attaching the accessory nose cap to the tip of
the push lever and when detaching it, make sure to
disconnect the hose beforehand. It is very dangerous
for a nail to be fired by mistake.
01Eng_NV90AG_WE.p65 1/31/13, 14:318
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NV90AG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV90AG in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info