568914

Hitachi NV90AB Manual

6
Zoom out
Zoom in
Previous page
1/56
Next page
5
English
HOW TO USE THE NAILER
CAUTIONS:
⅜ Never use the head or body of this device as a
hammer.
⅜ Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Nailing procedures
(1) Method of intermittently driving nails (single shot)
The single-contact change lever is in the single shot
position (See Fig. 8)
This nailer includes a single shot structure to allow
striking of a single nail by pushing down the push
lever and pulling the trigger (see Fig. 7).
CAUTION:
⅜ [Method of intermittently driving nails (single shot)]
explained here is not [Sequential fire]. When Single-
contact Change Lever is at the Single shot position, if
the push lever is pushed up in a state where the
trigger is pulled, only one piece of nail in the shooting
muzzle is fired: Be careful!
In the event it is used by Sequential fire, use the
Sequential Fire Parts Set of Optical Accessory.
⅜ If you do not pull the trigger quickly and crisply while
in the single shot mode, the nailer will bounce and
shoot several nails instead of just one. To avoid this,
be sure to pull the trigger quickly and crisply.
Fig. 7
Fig. 8
⅜ Push lever
When depressing the nail outlet, be sure to fully lift
the push lever (see Fig. 7) to release the safety lock.
Thus, nails cannot be driven without releasing the
safety lock even though the trigger is pulled.
(2) Method for continuous driving of nails (contact drive)
The single-contact change lever is in the contact
driving position (See Fig. 10).
Use the accessory hexagon bar wrench to turn the
single-contact change lever to the contact driving
position.
First pull back the trigger. Then press the nail outlet
on the place to drive nails. Driving of nails will start.
(Fig. 9)
Fig. 9
Fig. 10
CAUTION:
Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
NOTES:
⅜ Precautions on no-load operation
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed “no-load operation”. Such operation
may deteriorate the bumper, magazine, and nail
feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all
nails should be removed after using this nailer.
⅜ After completing operation, put into the body about
2cc oil through the hose joint to protect the tool from
rust.
⅜ Under low temperature conditions, the machine
sometimes does not operate correctly. Always operate
the machine at the appropriate ambient temperature.
2. How to use nosecap
CAUTION:
Remove the hose from the nailer and release the
compressed air before installing or removing the
nosecap to prevent accidental nail ejection.
⅜ Attach the nose cap (A) on the tip of the push lever
when you wish to protect the surface of wood, etc.,
from scratches.
Trigger
Push Lever
Contact Driving Position
Single-Contact
Change Lever
Single-Contact
Change Lever
Single Shot Position
Next, depress the
nail outlet
First, pull the Trigger
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NV90AB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV90AB in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info