Manual Hitachi NV75AG (page 9 of 46) (English, German, Dutch, French, Italian, Spanish)

568911

Zoom out

Zoom in

1/46

English

⅜ Wall and roof sheathing

⅜ Mobile home and modular housing construction

⅜ Crate and pallet construction

NOTE

3.3 mm × 76 mm (.131" × 3") nails cannot be driven in

some cases, depending on the material. Test drive

some of the nails first to check before using.

PREPARATION PRIOR TO OPERATION

1. Prepare the hose

Be sure to use the hose provided with minimum 7

mm (9/32”) inside diameter.

NOTE

The air supply hoses must have a minimum working

pressure rating of 12.8 bar (180 psi) or 150 percent of

the maximum pressure produced in the air supply

system, whichever is higher.

2. Check on safety

CAUTIONS

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the exhaust

cover, etc. for tightness.

Check the nailer for air leaks and defective or rusty

parts.

⅜ Check whether or not the push lever works correctly.

Also check whether or not any dirt has adhered to the

moving parts of the push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Check the air pressure

CAUTION

The air pressure must be constantly maintained at

4.9 – 8.3 bar (70 – 120 psi.).

Adjust the air pressure between 4.9 to 8.3 bar (70 ~

120 psi.) according to the diameters and length of

nails and hardness of the wood being nailed. Pay

special attention to the output pressure, capacity,

and piping on the air compressor, so that air pressure

does not exceed the specified limit. Note that

excessive pressure may affect overall performance,

service life, and safety.

2. Lubrication

(1) Prior to operating this nailer, be sure to provide an air

set between the air compressor and this device.

Lubrication through the air set offers smooth

operation, extended service life, and anticorrosion.

Adjust the oiler so that a single drop of oil is supplied

at intervals of 5 to 10 nailing cycles.

Dimensions of nails

STANDARD ACCESSORIES

(1) Eye protector .............................................................. 1

(2) Hexagon bar wrench for M4 screw ........................... 1

(3) Hexagon bar wrench for M5 screw ........................... 1

(4) Hexagon bar wrench for M6 screw ........................... 1

(5) Oiler ............................................................................. 1

(6) Nose cap ..................................................................... 1

OPTIONAL ACCESSORY

⅜ Sequential Trip Mechanism Kit (Code No. 883-991)

(Sequential Fire Parts Set, Single Shot Parts)

With the sequential fire parts,the nail is driven only

by squeezing the trigger after pushing down the

push lever.

By installing these parts, driving nails into improper

positions and unexpected firing of nails caused by

accidental operation of the push lever can be

prevented.

APPLICATIONS

⅜ Floor and wall flaming

⅜ Siding, fencing, decking

NAIL SELECTION

Wire collated nails and plastic collated nails can be driven

with this tool.

Choose a suitable nail from Fig. Nails which are not

shown in Fig. can not be driven with this tool. Nails are

linked and rolled.

SPECIFICATIONS

Type of power Piston reciprocating

Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)

Applicable nails ref. Fig.

Amount of loadable nails 200 – 300 nails (1 coil)

Size 271 mm (L) × 338 mm (H) × 132 mm (W) (10-11/16” × 13-5/16” × 5-3/16”)

Weight 2.5 kg (5.5 lbs)

Nail-feeding method Piston reciprocation

Hose (inside diam.) 7 mm (9/32”)

Wire-collatd coil nails Sheet-collated coil nails

MIN. MAX. MIN. MAX.

6 mm 7.2 mm 5.7 mm 6 mm

(.236”) (.283”) (.224”) (.236”)

57 mm (2-1/4”)

2.3 mm

(.090”)

2.5 mm

(.099”)

75 mm (3”)

45 mm (1-3/4”)

3.3 mm

(.131”)

2.5 mm

(.099”)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV75AG in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 8,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NV75AG Manual

Product: