568910

Hitachi NV65AH Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
5
English
NOTE:
Be careful not to deform the collated wires and not to
disengage the nails with the guide surface.
Otherwise, the nail guide will not close correctly.
4 Pulling the nails to the right, swing the nail guide
closed. (Fig. 6)
(7) Lock the knob completely.
HOW TO USE THE NAILER
CAUTIONS:
⅜ Never use the head or body of this device as a
hammer.
⅜ Take precautions to ensure the safety of persons in
the vicinity during operation.
1. This Nailer is equipped with the push lever and does
not operate unless the push lever is depressed
(upward position).
There are two methods of operation to drive nails
with this Nailer.
They are:
1. Intermittent operation (Trigger fire)
2. Continuous operation (Push lever fire)
(1) Intermittent operation (Trigger fire)
1 Position the nail outlet on the workpiece with
finger off the trigger.
2 Depress the push lever firmly until it is completely
depressed.
3 Pull the trigger to drive a nail.
4 Remove finger from the trigger.
To drive another nail, move the Nailer along the
workpiece and repeat this procedure. (Fig. 7)
Fig. 7
(2) Continuous operation (Push lever fire)
1 Pull the trigger with the Nailer off the workpiece.
2 Depress the push lever against the workpiece to
drive a nail.
3 Move the Nailer along the workpiece with a
bouncing motion.
Each depression of the push lever will drive a
nail.
As soon as the desired number of nails have been
driven, remove finger from the trigger. (Fig. 8)
Fig. 8
CAUTION:
Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
NOTES:
⅜ Precautions on no-load operation
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed “no-load operation”. Such operation
may deteriorate the bumper, magazine, and nail
feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all
nails should be removed after using this nailer.
⅜ After completing operation, put into the body about
2cc oil through the hose joint to protect the tool from
rust.
⅜ Under low temperature conditions, the machine
sometimes does not operate correctly. Always operate
the machine at the appropriate ambient temperature.
2. Adjusting the nail-driving depth
CAUTIONS:
When making adjustments, be sure remove your
finger from the trigger. When making adjustments,
be sure that the nail outlet is not facing downward
and that body parts or other persons are not in the
path of the nail outlet.
⅜ Adjusting the adjuster (Fig. 9)
Carry out test driving. If the nails are too deep, turn
the adjuster to the shallow side (
mark).
If the nail depth is too shallow, turn the adjuster to
the deep side ( mark). (See Fig. 9, 10)
Depth is changed 1 mm with each rotation of the
adjuster.
Fig. 9
Adjuster
Deep
Shallow
Push Lever
Trigger
Previously pull
the trigger
2
3
1
3
01Eng_NV65AH_WE 9/11/11, 2:47 PM5
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NV65AH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV65AH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info