568908

Hitachi NV50AH Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
5
English
HOW TO USE THE NAILER
CAUTIONS:
⅜ Never use the head or body of this nailer as a
hammer.
⅜ Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Nailing procedures
(1) Method of intermittently driving nails (single shot)
The single-contact change lever is in the single shot
position (see Fig. 8).
This nailer includes a single shot structure to allow
driving of a single nail by pushing down the push lever
and pulling the trigger (see Fig. 7).
CAUTIONS:
⅜ [Method of intermittently driving nails (single shot)]
explained here is not [Sequential fire]. When Single-
contact Change Lever is at the Single shot position, if
the push lever is pushed up in a state where the trigger
is pulled, only one piece of nail in the shooting muzzle
is fired: Be careful!
In the event it is used by Sequential fire, use the
Sequential Fire Parts Set of Optical Accessory.
⅜ If you do not pull the trigger quickly and crisply while
in the single shot mode, the nailer will bounce and
shoot several nails instead of just one. To avoid this,
be sure to pull the trigger quickly and crisply.
Fig. 7
Fig. 8
⅜ Push lever
When depressing the nail outlet, be sure to fully lift the
push lever (see Fig. 7) to release the safety lock. Thus,
nails cannot be driven without releasing the safety
lock even though the trigger is pulled.
(2) Method for consecutive driving of nails (contact drive)
The single-contact change lever is in the contact driv-
ing position (see Fig. 10).
Use the accessory hexagon bar wrench to turn the
single-contact change lever to the contact driving
position.
First pull back the trigger. Then press the nail outlet on
the workpiece. Driving of nails will start. (Fig. 9)
Fig. 9
Fig. 10
CAUTION:
Exercise care when nailing corners of lumber. When
consecutive nailing is carried out at corners of lumber,
a nail may go astray or break through the corner.
NOTES:
⅜ Precautions on no-load operation
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed “no-load operation”. Such operation
may deteriorate the bumper, magazine, and nail feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all nails
should be removed after using this nailer.
⅜ After completing operation, put into the body about
2cc oil through the hose joint to protect the tool from
rust.
⅜ Under low temperature conditions, the machine some-
times does not operate correctly. Always operate the
machine at the appropriate ambient temperature.
2. Adjusting the nail-driving depth
CAUTION:
When making adjustments, be sure to remove your
finger from the trigger. When making adjustments, be
Trigger
Push Lever
Single Shot
Position
Single-Contact
Change Lever
First, pull the Trigger
Next, depress the
nail outlet
Contact Driving
Position
Single-Contact
Change Lever
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi NV50AH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV50AH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info