Manual Hitachi NV45AB2 (page 8 of 56) (English, German, Dutch, French, Italian, Spanish)

568902

Zoom out

Zoom in

1/56

English

Fig. 13

(2) Open the nail guide and remove dust, etc., as shown

in Fig. 14. Apply lubricant to the sliding groove of the

feeder and feeder shaft. Check the main nail stopper

and sub nail stopper slide smoothly by pushing them

with your finger.

Fig. 14

(3) Also, apply the recommended oil to the feeding sur-

face of the nose and nail guide after cleaning. This

promotes smooth operation and retards corrosion.

CAUTION:

Check for smooth movement of the feeders and

stoppers before use. If movement is uneven, nails

could be fired at an irregular angle, presenting a

hazard to the operator and others nearby.

5. Cleaning and removal of tar and dirt

Adhesion of tar and dirt to areas around the discharge

outlet, push lever or nail feed parts will interfere with

proper operation.

Please clean and remove tar and dirt with kerosene, #2

fuel oil or diesel fuel.

CAUTION

⅜ Never use gasoline or other similar highly volatile

liquids for cleaning. Vapors of such liquids inside the

power tool could be ignited by sparks produced during

nailing and cause an explosion.

⅜ Never use kerosene to oil the tool.

(1) Please immerse only the area around the discharge

outlet in solvent and do not immerse the cylinder or

magazine.(See Fig. 15)

Nail Guide

Knob

Nail Guide

Sub Nail Stopper

Feeder Shaft

Feeder

Nose

Main Nail Stopper

Fig. 15

CAUTION

⅜ Do not immerse the nailer in solvent. Plastic parts and

the O-ring etc. may be demaged.

(2) Throughly dry the power tool. If any oily film from the

solvent remains, it will promote adhesion of tar and

frequent cleaning will be necessary.

(3) After cleaning check that the push lever, the spring to

return the push lever, and the feeder move smoothly.

CAUTION

⅜ The push lever must be free to move without sticking

or binding. The spring must positively return the push

lever to its down position whenever the push lever is

released from being held in its up position.

6. Inspecting the magazine

Clean the magazine. Remove dust of wooden chips

which may have accumulated in the magazine.

7. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When ot in use, the Nailer should be stored in a warm

and dry place.

Keep out of reach of children.

8. Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the tool

to the Hitachi Authorized Service Center when re-

questing repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

Body

Push

Lever

Outlet

Magazine

Nose

01Eng_NV45AB2_WE 3/24/09, 14:557

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NV45AB2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NV45AB2 Manual

Product: