Manual Hitachi NT65MA3 (page 11 of 54) (English, German, Dutch, French, Italian, Spanish)

568898

Zoom out

Zoom in

1/54

English

5 DISCONNECT AIR HOSE FROM NAILER.

6 Choose a suitable position for the adjuster.

3. Using the blow nozzle

CAUTION

⅜ Be sure to release your finger from the trigger before

using the blow nozzle.

⅜ Do not point the air outlet at a person.

⅜ Do not use the blow nozzle with the push lever left fit.

This Nailer has a blow nozzle that blows out wood

shavings which occur during work.

Press the knob with your thumb to use the blow nozzle

(See Fig. 8).

NOTE

⅜ When the blow nozzle is used for a long time, the

nailing force may degrade temporarily. In this case,

allows the air supply pressure to stabilize before

starting work.

⅜ Oil in the body or drained water from the compressor

can sometimes spout out of the air outlet. It is

recommended that you once conduct a test before

use and see if such phenomenon happens at an

environment where spouted oil will cause any

inconvenience.

4. Changing the exhaust direction

The direction of the exhaust vent can be changed by

turning the top cover (See Fig. 9).

5. Using the nose cap (See Fig. 10)

If you like to protect the surface of workpiece against

scratches or markings made by the push lever, attach

the accessory nose cap to the push lever.

(1) DISCONNECT AIR HOSE FROM NAILER.

(2) Put in the nose cap in the direction of the arrow as

shown in the diagram.

(3) The nose cap is marked to indicate the exit point of

the nail, making alignment easier.

⅜ Pull out the tip of the push lever in the reverse order

of attachment.

When not using the nose cap, attach to the storage area

in back of the magazine (See Fig. 11).

INSPECTION AND MAINTENANCE

CAUTION

Be sure to disconnect the hose during cleaning

jams, inspection, maintenance and cleaning.

1. Countermeasure for nail jamming

(1) DISCONNECT AIR HOSE.

(2) Remove all nails.

(3) Release the lock lever and open guide plate (A) (See

Fig. 12).

(4) Remove the jammed nail with a slotted-head

screwdriver (See Fig. 13).

(5) Close guide plate (A) and latch.

(6) In case of frequent jams, consult the Authorized

Service Center from which you bought this machine.

2. Inspecting the magazine

Clean the magazine. Remove dust or wooden chips

which may have accumulated in the magazine. Apply

oil occasionally to the nail rail (See Fig. 14).

3. Check on mounting screws for each part

At regular intervals check every part for loose

mounting screws and whether or not there are any

air leaks. Retighten any loose screws. Operating the

equipment with loose screws untightened will incur

a hazard.

4. Inspecting the push lever

Check if the push lever can slide smoothly.

Clean up the sliding area of the push lever and use the

provided oil for lubrication from time to time.

Lubrication enables smooth sliding and simultaneously

serves to prevent the formation of rust.

5. Storing

⅜ When not in use for an extended period, apply a thin

coat of the lubricant to the steel parts to avoid rust.

⅜ Do not store the Nailer in a cold weather environment.

Keep the Nailer in a warm area.

⅜ When not in use, the Nailer should be stored in a

warm and dry place.

Keep out of reach of children.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

COMPRESSOR

CAUTION

When the maximum, operating pressure of the air

compressor exceeds 8.3 bar (120 psi.), be sure to

provide a reducing valve between the air compressor

and nailer. Then, adjust the air pressure within the

operating range of 4.9 – 8.3 bar (70 – 120 psi.). If the

air set is installed, lubrication is also possible, thus

providing additional convenience.

OILER-FILTER-REDUCING VALVE (Air Set)

So that the equipment can be operated under an optimum

condition to ensure extended service life, it is

recommended to use an oiler filter reducing valve. Please

limit the length of the hose between the unit and the air

set to within 10 m when using (See Fig. 15).

APPLICABLE LUBRICANTS

Type of lubricant Name of lubricant

Recommended oil SHELL TONNA

Motor oil SAE10W, SAE20W

Turbine oil ISO VG32 – 68

(#90 – #180)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NT65MA3 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NT65MA3 Manual

Product: