Manual Hitachi NT65M2S (page 8 of 54) (English, German, Dutch, French, Italian, Spanish)

568896

Zoom out

Zoom in

1/54

English

at all, it is dangerous to discharge the tool while

pointing it at someone, so never attempt to do so. No

horseplay. Respect the tool as a working implement.

9. Before using the power tool, check the push lever.

Before using the power tool make sure to check that

the push lever and valve operate properly. Without

nails loaded into the power tool, connect the hose

and check the following. If the sound of operation

occurs this indicates a fault, so in such a case do not

use the power tool until it has been inspected and

repaired.

⅜ If merely pulling the trigger causes operating

sound of driver blade movement occur, the power

tool is faulty.

⅜ If merely pushing the push lever against the

material to be nailed causes the sound of driver

blade movement to occur, the power tool is faulty.

Furthermore, with regard to the push lever, please

note that it must never be modified or removed.

10. Use specified nails only.

Never use nails other than those specified and

described in these instructions.

11. Be careful when connecting the hose.

When connecting the hose and loading nails in order

not to fire the tool by mistake, make sure of the

followings.

⅜ Do not touch the trigger.

⅜ Do not allow the firing head to contact with any

surface.

⅜ Keep the firing head down.

Strictly observe the above instructions, and always

make sure that no part of the body, hands or legs

is ever in front of the nail outlet.

12. Do not carelessly place your finger on the trigger.

Do not place your finger on the trigger except when

actually nailing. If you carry this tool or hand it to

someone while having your finger on the trigger,

you may inadvertently discharge a nail and thus cause

an accident.

13. Press the nail outlet firmly against the material to be

nailed.

When driving in nails, press the nail outlet firmly

against the material to be nailed. If the outlet is not

applied properly, the nails may rebound.

14. Keep hands and feet away from the firing head when

using.

It is very dangerous for a nail to hit the hands or feet

by mistake.

15. Beware of the tool’s kickback.

Do not approach the top of the tool with your head

etc. during operation. This is dangerous because the

tool may recoil violently if the nail currently being

driven in comes into contact with a previous nail or a

knot in the wood.

16. Take care when nailing thin boards or the corners of

wood.

When nailing thin boards, the nails may pass right

through, as may also be the case when nailing the

corners of wood due to deviation of the nails. In such

cases, always make sure that there is no one (and

nobody’s hands or feet; etc.) behind the thin board or

next to the wood you are going to nail.

17. Simultaneous nailing on both sides of the same wall

is dangerous.

Under no circumstances should nailing be performed

on both sides of a wall at the same time. This would

be very dangerous since the nails might pass through

the wall and thus cause injuries.

18. Do not use the power tool on scaffoldings, ladders.

The power tool shall not be used for specific

application for example:

– when changing one driving location to another

involves the use of scaffoldings, stairs, ladders or

ladder alike constructions, e.g. roof laths,

– closing boxes or crates,

– fitting transportation safety systems e.g. on

vehicles and wagons

19. Do not disconnect the hose with your finger on the

trigger.

If you disconnect the hose with your finger on the

trigger, the next time the hose is connected, there is a

danger that the power tool will fire a nail

spontaneously, or operate incorrectly.

20. Disconnect the hose and take out any nails left in the

magazine after use.

Disconnect tool from air before doing tool

maintenance, cleaning a jammed fastener, leaving

work area, moving tool to another location, or after

use. It is very dangerous for a nail to be fired by

mistake.

21. When removing a nail which has become stuck, make

sure to first of all disconnect the hose and release

compressed air.

When removing a nail which has become stuck in the

nail outlet, first of all make sure to disconnect the

hose and release compressed air inside the power

tool.

Accidental firing of the nail could be very dangerous.

22. A female plug (air socket) should not be used in the

body.

If a female plug is installed in the body, the

compressed air sometimes can not be drawn when

the hose is disconnected so avoid this.

The tool and air supply hose must have a hose

coupling such that all pressure is removed from the

tool when the coupling joint is disconnected.

23. When attaching and detaching the nose cap,

disconnect the hose.

When attaching the accessory nose cap to the tip of

the push lever and when detaching it, make sure to

disconnect the hose beforehand. It is very dangerous

for a nail to be fired by mistake.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NT65M2S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NT65M2S Manual

Product: