Manual Hitachi NT65A2 (page 5 of 40) (English, German, Dutch, French, Italian, Spanish)

568891

Zoom out

Zoom in

1/40

English

(3) After inserting the nails, pull the nail feeder up in

backward direction, remove it from the roll pin, move

it slowly forward and push the nail.

NOTE:

After having removed the nail feeder from the roll pin

and moving it forcefully forward, the nail coupling

may brake and the nail feeder may get caught between

the magazine and nails, causing poor nail feeding.

Therefore, move the nail feeder slowly forward.

CAUTIONS

⅜ To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a work

bench on floor. Also, never face the nail outlet toward

any part of a person.

⅜ Use nails in which five nails are connected.

HOW TO USE THE NAILER

CAUTIONS

⅜ Never use the head or body of this device as a hammer.

⅜ Take precautions to ensure the safety of persons in the

vicinity during operation.

1. Nailing procedures

(1) Intermittent nailing

Depress the nail outlet onto the desired point; then

pull the trigger to drive a nail in a single shot. (See Fig.

Fig. 3

CAUTION

This tool will sometimes fire twice in rapid succession

when strongly pressed flush against a surface or

when using on hard materials. In such cases, fire the

nails by squeezing and quickly releasing the trigger.

(2) Push lever

When depressing the nail outlet, be sure to fully lift the

push lever (See Fig. 3) to release the safety lock. Thus,

nails cannot be driven without releasing the safety

lock even though the trigger is pulled.

(3) Continuous nailing

First, pull the trigger. Then depress the devise onto the

desired position to automatically drive nails. (See Fig.

4).

Fig. 4

CAUTION

Excercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

NOTES

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the damper, magazine, and nail feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all nails

should be removed after using this nailer.

⅜ After completing operation, put into the body about

2cc oil through the hose joint to protect the tool from

rust.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. Attachment and detachment of the nose cap

CAUTIONS:

⅜ When attaching and detaching the nose cap, make

sure to disconnect the hose to release the compressed

air.

⅜ When attaching and detaching the nose cap, make

sure to take your finger off the trigger.

When you do not want to cause scratches in the material

you work with, use the accessory rubber nose cap. To

attach the nose cap, attach it as shown in Fig. 5. Detachment

shall be made in reversed order. Also, when attaching the

nose cap, the drive bit projection of the nail outlet will be

reduced and the nailing power will be lowered. Adjust the

nailing power according the air pressure used and the

attachment position of the bit guide.

Fig. 5

Push Lever Trigger

Previously pull the trigger.

Nose Cap

Disconnect air hose

Push Lever

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NT65A2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NT65A2 Manual

Product: