Manual Hitachi NT1865DBAL (page 15 of 204) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

661492

Zoom out

Zoom in

1/204

English

5 Remove the battery from the Nailer.

6 Choose a suitable position for adjuster.

3. Using the hook (See Fig. 21, 22, 23)

WARNING

When using the hook, turn oﬀ the power switch (green

light “OFF”). Pay suﬃ cient attention so that the main

equipment does not fall.

If the tool falls, there is a risk of accident.

Hook can be installed on the left or right side.

1 Remove the battery, then remove all remaining nails

from the magazine.

2 Securely hold the main unit and remove the screw using

a screwdriver. (See Fig. 21)

3 Remove the hook and hook plate. (See Fig. 22)

4 Install the hook on the other side and securely fasten

with screw. (See Fig. 23)

NOTE

Hook can be used as a hanger.

4. Using the nose cap (See Fig. 24, 25)

WARNING

When attaching or detaching the nose cap, be sure

to remove your ﬁ nger from the trigger and remove all

remaining fasteners and the battery from the nailer.

If you like to protect the surface of workpiece against

scratches or markings made by the push lever, attach the

accessory nose cap to the push lever.

1 Remove all remaining fasteners and battery from nailer.

2 Put the nose cap to the toe of the push lever.

3 The nose cap is marked to indicate the exit point of the

nail, making alignment easier.

4 When not using the nose cap, secure in the storage

compartment located on the reverse side of the

magazine.

NOTE

The nose cap may reduce nailing depth due to its

thickness. Re-adjustment of nailing depth is required.

5. Clearing a jam

If nails are jammed in ﬁ ring head, remove it, and adjust

the nailing in the following order.

CAUTION

Remove the battery from the Nailer.

1 Remove the battery from the Nailer.

2 Remove all nails.

3 Release the Lock lever and open guide plate. (See Fig.

26)

4 Remove the jammed nail with a slotted-head screwdriver.

(See Fig. 27)

CAUTION

○ NEVER hit the driver blade.

○ NEVER point the tool at yourself or another person, to

avoid risk of injury by mis-ﬁ ring.

Even if the battery is removed from the nailer, there is still

energy of compressed air remaining inside.

5 Close guide plate and latch.

NOTE

In case of frequent jam, contact a Hitachi authorized

service center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to remove all remaining fasteners and battery

from the nailer before maintenance and inspection.

1. Inspecting the magazine

1 Remove battery from the Nailer.

2 Clean the magazine. Remove dust and wooden

chips which may have accumulated in the magazine.

CAUTION

Check that the nail feeder slides smoothly by pulling it

with ﬁ nger.

If not smooth, nails can be driven at an irregular angle

and hurt someone.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

0000Book_NT1865DBAL.indb 150000Book_NT1865DBAL.indb 15 2017/04/14 15:11:322017/04/14 15:11:32

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi NT1865DBAL in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi NT1865DBAL Manual

Product: