78986

Hitachi M 6 SB Manual

7
Zoom out
Zoom in
Previous page
1/38
Next page
6
English
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Trimmer guide ass'y ................................................ 1
(2) Straight Guide ........................................................... 1
(3) Template Guide (with two M4 screws) ................ 1
(4) Wrench 17/19 mm .................................................... 1
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜
Plywood trimming
⅜ Various beveling
⅜ Various grooving
⅜ Engraving
⅜ Cut offs
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting the bit
Refer to "Fitting and removal of the bit" section
given in the following. It is dangerous if the bit is
not fitted to the coIlet chuck securely. Check if the
collet chuck is sufficiently tightened.
5. Cutting using the workpiece edge as a base line
(Fig. 1)
Note that the distance between the machine center
and the hollow differs from the other three distances.
6. Confirm the spindle lock mechanism.
Confirm that the spindle lock is disengaged by
pushing the push button two or three times before
switching the power tool on. (See Fig. 2)
FITTING AND REMOVAL OF THE BIT
1. Fitting the bit
(1) Remove the base ass'y from the body. When
loosening the wing nut (See Fig. 3), the base ass'y
can be removed.
(2) Deeply inset the bit into the collet chuck hole. (The
distance is 15 mm or more from side of collet
chuck.)
(3) Depress spindle lock (Fig. 2) and rotate collet nut
clockwise by hand until lock engages hole in motor
spindle.
(4) While holding spindle lock engaged, tighten collet
nut securely by turning clockwise using wrench
provided.
CAUTIONS
⅜ Make sure to tighten the collet chuck after inserting
the bit. Collet chuck may be damaged if it is tightened
without inserting the bit.
⅜ Avoid depressing the lock pin while the bit is still
in rotation. Because, there is a fear that doing so
may result in an abnormal noise or damage in the
fixed section of the rotating shaft.
(5) Fit the removed base assembly to the rack provided
on the body's outer housing after adjusting the
pinion of the base assembly thereto. Then tighten
the wing nut and fix the assembly securely.
2. Removal of the bit
Loosen the collet chuck in the reverse manner as
described for the fitting the bit.
CAUTION
Bit is heated after the cutting work.
Do not touch it directly.
Voltage (by areas)* (110V, 230V, 240V)
Power Input* 440 W
No-load speed 30000 min
-1
Collet Chuck Capacity 6 mm or 6.35 mm (1/4")
Weight (Only main body) 1.4 kg
PRECAUTIONS ON USING TRIMMER
1. Always use the bit of correct shank diameter suitable
for the speed of the tool.
2. Hold the body firmly during operation. Otherwise,
injuries can result.
3. The bit is very hot immediately after operation.
Avoid bare hand contact with the bit for any reason.
4. Avoid bringing your hand, face, etc., close to the
bit and rotary parts during operation.
5. Exercise caution as the bit remains rotating even
after the switch is turned off. Contact of your hand,
etc., with the rotating bit can result in injuries.
01Eng_M6SB_WE 5/14/07, 17:186
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi M 6 SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi M 6 SB in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info