572195
32
Zoom out
Zoom in
Previous page
1/55
Next page
English - 31 -
cancel, press BLUE button. The following menu
will be displayed during the automatic tuning:
After APS is nalized, the programme table
will appear on the screen. In the programme
table you will see the programme numbers and
names assigned to the programmes.
If you do not accept the locations and/or the
programme names, you can change them via
the program table.
Manual Channel Scan
In manual channel scan, the number of the
multiplex is entered manually and only that
multiplex is searched for the channels. For every
valid channel number, signal
level and signal
quality are shown on the screen.
In both manual and auto search any existing
channel in the database is not re-stored to avoid
redundant duplicates of that channel.
Clear Service List (*)
(*) This setting is visible only when the Country
option is set to Denmark, Sweden, Norway or
Finland.
Use this setting to clear channels stored.
Press
” or “ ” button to select Clear Service
List and then press OK. The following OSD
message will be displayed on the screen:
Are you sure you want to delete all channels?
Press OK to cancel.
Select Yes by pressing
” or “ button and
press OK to delete all of the channels.
First Time Installation
The user can use this item to load default
settings, which were loaded to the receiver at
the factory.
To install factory settings, highlight “First Time
Installation” menu item and press OK button,
then you will be asked whether or not to delete
the settings. Selecting “Yes” by pressing OK
button while the “Yes” is highlighted will delete
the existing channel table.
Then you will be asked to con rm for deleting
all channels and settings:
By selecting Yes and pressing the OK button,
the existing channel table will be deleted.
After factory settings are loaded, “First Time
Installation” menu will be displayed.
The menu which is displayed for language
selection appears on the screen at rst. By using
” or “ ” buttons, select the desired language
option, and press OK button to activate.
“First time installation” OSD will appear on the
screen. By pressing “
” or “ ” buttons, select
the Country you want to set and press OK
button (** only for EU countries).
- Next, active antenna mode selection OSD will
appear on the screen.Use ” or “ to set and
press OK to continue.See the section, “Initial
Settings” for more information.
After active antenna mode option is selected, a
message asking for automatic search appears
on the screen:
Press the OK button to start installation. After
search is completed for digital channels, a
message asking whether to search for analogue
channels appears on the screen:
Press the OK button to search for analogue
channels. The following menu appears on the
screen for analogue channel search:
01_[GB]_MB35_UKIDTV_BRONZE3_32856W_1800UK_10066012_50158149.indd 3101_[GB]_MB35_UKIDTV_BRONZE3_32856W_1800UK_10066012_50158149.indd 31 21.10.2009 10:37:2721.10.2009 10:37:27
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi L32HP03UA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi L32HP03UA in the language / languages: English as an attachment in your email.

The manual is 4,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info