511990

Hitachi H90SC Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
4
English
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Input* 1450W
Full-load impact rate 850/min.
Weight (without cord) 32 kg
SPECIFICATIONS
* Be sure to check the nameplate on this Demolition Hammer as it is subject to change by areas.
DEMOLITION HAMMER SAFETY WARNINGS
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
4. Before starting to break, chip or drill into a wall, floor
or ceiling, thoroughly confirm that such items as
electric cables or conduits are not buried inside.
5. Properly set the bit holder
6. At the start of work, confirm screw tightening.
7. When working at a highly elevated location, pay
attention to articles and persons below.
8. Wear protective shoes to protect your feet.
STANDARD ACCESSORIES
(1) Hexagon Bar Wrench for M12 .................................. 1
(2) Hexagon Bar Wrench for M6 .................................... 1
(3) Hexagon Bar Wrench for M4 .................................... 1
(4) Side Handle ................................................................ 1
(5) Bolt .............................................................................. 4
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES
(sold separately)
1. Bull point
Total length: 410, 520 mm
2. Cold chisel
Total length: 520 mm
3. Scoop
Total length: 546 mm
4. Cutter
Total length: 520 mm
Width: 75 mm
5. Rammer + Shank
Total length: 520 mm
Outer diameter: 200 mm
6. Hammer grease 500g (in a can)
Optional accessories are subject to change without notice.
APPLICATIONS
This Demolition Hammer should be applied to
demolishing concrete, chiseling off concrete, grooving,
bar cutting installation of piping and wiring, sanitary
facility installation, machinery installation, water supply
and drainage work, interior jobs, harbor facilities and
other civil engineering works.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate of this Demolition Hammer.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, this Demolition Hammer
will start operating immediately, which could cause a
serious accident.
3. Extension cord
When the work area is remote from the power source,
use an extension cord of sufficient thickness and
rated capacity. The extension cord should be kept as
short as practicable.
4. Mounting an accessory, such as a bull point, a cutter,
etc.
(1) With the retainer directed backward, insert the
accessory shank portion into the hole on the front
cover. (Fig. 1)
01Eng_H90SC_WE 08/12/10, 17:054
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi H90SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H90SC in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info