511989
4
Zoom out
Zoom in
Previous page
1/33
Next page
3
English
PRECAUTIONS ON USING DEMOLITION HAMMER
1. Wear ear protectors.
Exposure to noise can cause hearing loss.
2 Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Do not touch the bit during or immediately after
operation. The bit becomes very hot during operation
and could cause serious burns.
4. Before starting to break, chip or drill into a wall, floor
or ceiling, thoroughly confirm that such items as
electric cables or conduits are not buried inside.
5. Properly set the bit holder
6. At the start of work, confirm screw tightening.
7. When working at a highly elevated location, pay
attention to articles and persons below.
8. Wear protective shoes to protect your feet.
STANDARD ACCESSORIES
(1) Bull Point .................................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
Asphalt Cutting
(1) Cutter
Overall Length: 410 mm
Width: 75 mm
Groove Digging and Edging
(1) Cold Chisel
Overall Length: 410 mm
Tamping
(1) Rammer
Outer diameter: 200 mm
Scooping Work
(1) Scoop
Overall Length: 380 mm
Grease
500 g (in a can)
70 g (in a tube)
30 g (in a tube)
Optional accessories are subject to change without notice.
APPLICATIONS
This Demolition Hammer should be applied to
demolishing concrete, chiseling off concrete, grooving,
bar cutting installation of piping and wiring, sanitary
facility installation, machinery installation, water supply
and drainage work, interior jobs, harbor facilities and
other civil engineering works.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate of this Demolition Hammer.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, this Demolition Hammer
will start operating immediately, which could cause a
serious accident.
3. Extension cord
When the work area is remote from the power source,
use an extension cord of sufficient thickness and
rated capacity. The extension cord should be kept as
short as practicable.
4. Mounting an accessory, such as a bull point, a cutter,
etc.
CAUTION:
Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident.
NOTE:
For accessories such as a bull point and a cutter, use
only Hitachi genuine parts.
(1) Clean, then smear the accessory shank portion with
grease or machine oil. (Fig. 1)
(2) Shank
Overall Length: 250 mm
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 1240W*
Full-load Impact Rate 1400/min.
Weight (without cord) 18 kg
SPECIFICATIONS
* Be sure to check the nameplate on this Demolition Hammer as it is subject to change by areas.
01Eng_H70SA_WE 4/20/07, 3:56 PM3
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi H70SA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H70SA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info