511986

Hitachi H65SB Manual

5
Zoom out
Zoom in
Previous page
1/37
Next page
4
English
SPECIFICATIONS
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 1240W*
Full-load Impact Rate 1400min
–1
Weight (without cord, side handle) 16 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Case ............................................................................ 1
(2) Bull Point ................................................................... 1
(3) Hexagon Bar Wrench (for 8mm bolt) .................. 1
(4) Hexagon Bar Wrench (for 4mm bolt) .................. 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
⅜ Asphalt Cutting
⅜ Groove Digging and Edging
⅜ Tamping
⅜ Scooping Work
⅜ Grease
500g (in a can)
30g (in a tube)
Optional accessories are subject to change without
notice.
APPLICATIONS
Demolishing concrete, chiseling off concrete, grooving,
bar cutting.
Application examples:
Installation of piping and wiring, sanitary facility
installation, machinery installation, water supply and
drainage work, interior jobs, harbor facilities and other
civil engineering works.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Mounting a tool
NOTE:
For tools such as a bull point and a cold chisel,
use only genuine HITACHI parts.
(1) Clean, then smear the tool shank with grease or
machine oil. (Fig.1)
(2) Rotate the stop lever 180° in a clockwise direction
while pulling it toward you. Next, insert the tool
shank into the hexagonal hole on the frontcover.
(Fig.1)
(3) Clamp the tool by turning the stop lever by half
a turn in the opposite direction. (Fig. 2)
HOW TO USE THE DEMOLITION HAMMER
1. Squeeze the trigger switch after applying the tip of
the bit to the crushing position.
In some cases, it is necessary to punch the tip of
the bit against the crushing position forcibly in
order to begin the striking motion.
This is not due to malfunction of the tool. It means
that the safe guard mechanism against no-load
striking is working.
2. Operate the tool by utilizing its empty weight. The
performance will not be better even if the tool is
pressed or thrust forcibly against the work surface.
Hold the tool with a force just sufficient to counteract
the reaction. (Fig. 3)
(1) Cutter
Overall Length: 410 mm
Width: 75 mm
(1) Scoop
Overall Length: 410 mm
(2) Shank
Overall Length: 250 mm
(1) Cold Chisel
Overall Length: 410 mm
Outer diameter: 200 mm
(1) Rammer
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi H65SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H65SB in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info