Manual Hitachi H60MC (page 7 of 44) (English, German, Dutch, French, Italian, Portuguese, Spanish)

511985

Zoom out

Zoom in

1/44

English

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Installing Tools

CAUTION

Be sure to switch power OFF and disconnect the

plug from the receptacle to avoid serious trouble.

NOTE

When using tools such as bull points, cutters, etc.,

make sure to use the genuine parts designated by

our company.

(1) Clean the shank portion of the tool.

(2) As shown in Fig. 1, pull grip (A) in the direction of

, and insert the tool into a hole of the front cap.

(3) Adjust the groove position while turning the tool, and

furthermore insert it until it hits the end of the hole.

(4) Return grip (A) to its original position, pull the tool

and make sure it is locked completely (Fig. 2).

5. Deciding Working Position of Tool

The tool can be turned every 30 degrees and can

be fixed at the position of 12 steps.

(1) As shown in Fig. 3, if the grip (A) is turned in the

direction of

in a state where the grip (B) is

pushed in the direction of

, the blade angle can

be changed freely to any desired position.

(2) Release grip (B) and turn the tool, and make sure

that it is locked completely.

6. Removing Tool

As shown in Fig. 1, pull grip (A), and pull out the

tool.

CAUTION

Be sure to grip the handle and side handle during

work. Do not hold by the grip (A) during work. If

you pull it by mistake, the bull point could jump out.

7. Move the side handle

For bar type handle

Fixing the side handle (Fig. 4)

(1) Rotate the side handle in a clockwise direction to

secure it.

(2) Set the side handle to a position that is suited to

the operation and then securely tighten the side

handle.

For D type handle

The side handle can be fixed at any desired position;

360 degrees, and can also be fixed at any position

in the back-and-forth direction.

(1) Loosen the handle by turning the grip in the direction

as shown in Fig. 5.

(2) Adjust it to a position where vertical (up-and-down)

operation can be facilitated as illustrated in Fig. 6,

Fig. 7, and Fig. 8.

(3) Turn the grip in the direction of

and fix the

handle.

HOW TO USE THE DEMOLITION HAMMER

(Fig. 9)

1. After placing the tip of the tool on concrete surface,

switch ON.

The switch can be turned ON if the trigger is pulled

and OFF when it is released.

If the stopper is pressed while the trigger for the

switch is pulled, even if your finger is released from

the trigger, the switch remains ON - convenient for

continuous operation.

To turn the switch OFF, pull the trigger again, and

then the stopper comes off.

2. By utilizing the empty weight of the machine and

by firmly holding the demolition hammer with both

hands, one can effectively control the subsequent

recoil motion.

Proceed at a moderate work-rate, the use of too

much force will impair efficiency.

CAUTION

After long time of use, the cylinder case becomes

hot. Therefore, be careful not to burn your hands.

GREASE REPLACEMENT

This machine is of full air-tight construction to protect

against dust and to prevent lubricant leakage. This

machine can be used without grease supplement for an

extended period of time. However, perform the grease

replacement to maintain the service life. Replace the

grease as described below.

1. Grease Replacement Period

You should look at the grease when you change

the carbon brush (See item 4 in the section

MAINTENANCE AND INSPECTION).

Ask for grease replacement at the nearest Hitachi

Authorized Service Center.

In the case that you are forced to change the grease

by yourself, please follow the following points.

2. How to replace grease

CAUTION

Before replacing the grease, turn the power off and

pull out the plug from the receptacle.

(1) Remove the crank cover and wipe off the old grease

inside. (Fig. 10)

(2) Supply 76 g (the standard volume to cover the

connecting rod) of Hitachi Electric Hammer Grease

A to the crank case.

(3) After replacing the grease, install the crank cover

securely. At this time, do not damage or lose the

oil seal.

NOTE

The Hitachi Electric Hammer Grease A is of the low

viscosity type. When the grease is consumed,

purchase from the Hitachi Authorized Service

Center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to switch power OFF and disconnect the

plug from the receptacle to avoid serious trouble.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or

replace the tool as soon as abrasion is noted.

01Eng_H60MC_WE 11/26/10, 9:326

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H60MC in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi H60MC

Hitachi H60MC User Manual - All languages - 104 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi H60MC Manual

Product: