568860

Hitachi H30PV Manual

6
Zoom out
Zoom in
Previous page
1/34
Next page
4
English
STANDARD ACCESSORIES
(1) Case ........................................................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
⅜ Demolishing
Bull point (Round type)
(SDS-plus shank)
Bull point (Square type)
(SDS-plus shank)
⅜ Groove digging and edging
Cold chisel (SDS-plus shank)
Cutter (SDS-plus shank)
⅜ Grooving
Grooving chisel (SDS-plus shank)
⅜ Hammer Grease A
500g (in a can)
70g (in a tube)
30g (in a tube)
Optional accessories are subject to change without
notice.
APPLICATIONS
Demolishing concrete, chiseling concrete, grooving, bar
cutting, and driving piles.
Application examples:
Installation of piping and wiring, sanitary facility
installation, machinery installation, water supply and
drainage work, interior jobs, harbor facilities and other
civil engineering work.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Installing Tools
CAUTION
To prevent accidents, make sure to turn the switch
off and disconnect the plug from the receptacle.
NOTE:
When using tools such as bull points, cutters, etc.,
make sure to use the genuine parts designated by
our company.
(1) Clean the shank portion of the tool.
(2) Insert the tool in a twisting manner into the tool
holder until it latches itself. (Fig. 1, 2)
(3) Check the latching by pulling on the tool. (Fig. 3)
5. Deciding Working Position of Tool
The tool can be turned every 30 degrees and can
be fixed at the position of 12 steps.
(1) As shown in Fig. 4, grip (B) is turned 60 degrees
in the direction of A, the blade angle can be changed
freely to any desired position. (Fig. 5)
(2) As shown in Fig. 6, return grip (B) in the direction
of A, and make sure that it is locked completely.
6. Removing Tool
As shown in Fig. 7, pull front cap in the direction
of A, and pull out the tool. (Fig. 8)
SPECIFICATIONS
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 720W*
Full-load Impact Rate 0–3800/min.
Weight (without cord, side handle) 4.2 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi H30PV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi H30PV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info