Manual Hitachi G23UAY (page 9 of 64) (English, German, Dutch, French, Italian, Portuguese, Spanish, Norwegian)

511970

Zoom out

Zoom in

1/64

English

SPECIFICATIONS

*1 Be sure to check the nameplate on product as it is subject to change by areas.

*2 Weight: Only main body

*3 The starting current limiter produces the starting current to such an extent that a fuse (16A, slow-blow)

is not tripped.

STANDARD ACCESSORIES

(1) Wrench ........................................................................ 1

(2) Side handle ................................................................ 1

(3) Hexagonal bar wrench ............................................. 1

Depressed center wheels are not provided as standard

accessories.

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜

Removal of casting fin and finishing of various types

of steel, bronze and aluminum materials and castings.

⅜ Grinding of welded sections or sections cut by

means of a cutting torch.

⅜ Grinding of synthetic resins, slate, brick, marble, etc.

⅜ Cutting of synthetic concrete, stone, brick, marble

and similar materials.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation.

[Installing and adjusting the wheel guard]

⅜ Open the lever and insert the locating pin of wheel

guard, bringing it into line with the across flats of

packing ground.

⅜ Then, turn the wheel guard to a desired position

(for use).

⅜ Close the lever and fix it. If and when required,

carry out adjustments by tightening or loosening

the screw.

⅜ If the lever does not move smoothly, apply some

lubricating oil to the sliding section between the set

piece and the lever.

⅜ Fasten the wheel guard at the position where the

across flats of the wheel guard positioning pin and

packing ground are aligned (the position where the

wheel guard is inserted), but do not use it.

5. Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface

defects. Also ensure that the depressed center wheel

is properly mounted and the wheel nut is securely

tightened, refer to the section on “Depressed Center

Wheel Assembly”.

6. Conducting a trial run

Ensure that the abrasive products is correctly

mounted and tightened before use and run the tool

at no-load for 30 seconds in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected.

If this condition occurs, check the machine to

determine the cause.

7. Confirm the spindle lock mechanism

Confirm that the spindle lock is disengaged by

pushing push button two or three times before

switching the power tool on (See Fig. 1).

8. Fixing the side handle

Screw the side handle into the gear cover.

Model G18SCY G18UAY G18SEY G18UBY G23SCY G23UAY G23SEY G23UBY

Voltage (by areas)*

(110V, 220V, 230V, 240V)

Input*

2400 W 2600 W 2400 W 2600 W

No-load speed 8500 min

-1

(/min) 6600 min

-1

(/min)

Outer dia. 180 mm 230 mm

Wheel Hole dia. 22.23 mm

Peripheral speed 80 m/s

Weight*

5.1 kg

Starting current limiter*

No Yes No Yes No Yes No Yes

01Eng_G18SCY_WE 4/16/10, 15:518

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi G23UAY in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi G23UAY Manual

Product: