Manual Hitachi G15YC2 (page 12 of 64) (English, German, Dutch, French, Italian, Portuguese, Spanish)

567033

Zoom out

Zoom in

1/64

English

ASSEMBLING AND DISASSEMBLING

ACCESSORIES (Fig. 3)

CAUTION: Be sure to switch OFF and disconnect the

attachment plug from the receptacle to avoid

a serious accident.

1. Assembling (Fig. 3)

(1) Turn the equipment upside-down so that the spindle

will be facing up.

(2) Mount the wheel washer onto the spindle.

(3) Fit the protuberance of the depressed center wheel

onto the wheel washer.

(4) Screw from above the wheel nut onto the spindle.

(5) As shown in Fig. 3, push in the push button to

prevent rotation of the spindle. Then, secure the

depressed center wheel by tightening the wheel nut

with the wrench.

2. Disassembling

Follow the above procedures in reverse.

Same as depressed center wheel.

1. Assembling (Fig. 3)

(1) Turn the equipment upside-down so that the spindle

will be facing up.

(2) After placing the sanding disc on the rubber pad,

thread the washer nut onto the spindle.

(3) Press the push button to secure the spindle and

tighten the washer nut with a wrench.

2. Disassembling

Follow the above procedures in reverse.

CAUTIONS

⅜ Confirm that the depressed center wheel is mounted

firmly.

⅜ Confirm that the push button is disengaged by

pushing push button two or three times before

switching the power tool on.

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of

cracks and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Inspecting the carbon brushes (Fig. 6)

The Motor employs carbon brushes which are

consumable parts. When they become worn to or

near the “wear limit”, it could result in motor

trouble. When an auto-stop carbon brush is

equipped, the motor will stop automatically. At that

time, replace both carbon brushes with new ones

which have the same carbon brush Numbers shown

in the figure. In addition, always keep carbon brushes

clean and ensure that they slide freely within the

brush holders.

4. Replacing carbon brushes (Fig. 7)

(1) Loosen the D4 tapping screw retaining the tail cover

and remove the tail cover.

(2) Use the auxiliary hexagonal wrench or small

screwdriver to pull up the edge of the spring that

is holding down the carbon brush. Remove the

edge of the spring toward the outside of the brush

holder.

(3) Remove the end of the pig-tail on the carbon brush

from the terminal section of brush holder and then

remove the carbon brush from the brush holder.

(1) Insert the end of the pig-tail of the carbon brush

in the terminal section of brush holder.

(2) Insert the carbon brush in the brush holder.

(3) Use the auxiliary hexagonal wrench or small

screwdriver to return the edge of the spring to the

head of the carbon brush.

NOTE:

Make sure the end of the spring is not holding the

pig-tail.

(4) Mount the tail cover and tighten the D4 tapping

screw.

5. Replacing supply cord

If the replacement of the supply cord is necessary,

this has to be done by the manufacturer of this

agent in order to avoid a safety hazard.

6. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

7. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATION:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

01Eng_G13YC2_WE 1/17/12, 8:2811

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi G15YC2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi G15YC2 Manual

Product: