567032

Hitachi G13YC2 Manual

10
Zoom out
Zoom in
Previous page
1/64
Next page
9
English
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
Electronic Control
The grinder has an electronic speed control which
provides:
⅜ full speed at all times in the range up to rated load.
⅜ soft-start.
⅜ Kickback Protection
The kickback protection feature cuts off the power
to the motor and stops the power tool in the event
of a sudden drop in the rotational speed of the
wheel during operation (for example, if the wheel
locks during cutting operation, etc.).
⅜ 0 Voltage Re-start Protection
The 0 voltage restart protection feature prevents the
power tool from restarting after the power has been
temporarily cut off during operation.
⅜ Overload Protection
The overload protection feature shuts off the power
to the motor in the event of overloading of the
motor or a conspicuous reduction in rotational speed
during operation.
NOTE:
The grinder is equipped with a rotational speed control
circuit. The rotational speed may fluctuate slightly due
to the conditions of use and working voltage.
STANDARD ACCESSORIES
(1) Depressed center wheel .......................................... 1
(2) Wrench ........................................................................ 1
(3) Side handle ................................................................ 1
(4) Hex. bar wrench ....................................................... 1
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜ Removal of casting fin and finishing of various
types of steel, bronze and aluminum materials and
castings.
⅜ Grinding of welded sections or sections cut by
means of a cutting torch.
⅜ Grinding of synthetic resins, slate, brick, marble, etc.
⅜ Cutting of synthetic concrete, stone, brick, marble,
and similar materials.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
NOTE:
When connected to the power supply, the built-in
electronic control circuit shifts to standby status and
the grinder becomes slightly warm, but this is not
a malfunction.
CAUTION
Do not operate from a direct current power source,
engine generator, booster or any other type of
transformer. Doing so may not only cause damage
to the grinder, but may lead to accidents.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
When the kickback protection, 0 voltage re-start
protection or overload protection feature has been
activated, return the power switch to the OFF position
and wait for 1 second or more before re-starting
the power tool.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent
injury should the depressed center wheel be
shattered during operation. Ensure that the wheel
guard is properly fitted and fastened before
commencing grinding operation.
Model G13YC2 G15YC2
Voltage (by areas)* (110V, 230V, 240V)
Power Input* 1500 W
No-load speed* 10500 min
-1
9000 min
-1
Wheel
outer dia. × hole dia. 125 × 22.23 mm 150 × 22.23 mm
peripheral speed 80 m/s
Weight (only main body) 2.0 kg
– Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, first disconnect the tool
from the mains supply (use non metallic objects)
and avoid damaging internal parts;
– Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn;
– Pay attention to the wheel that continues to rotate
after the tool is switched off.
CAUTION
When using a abrasive cutting wheel, be sure to
remove the standard accessory wheel guard and
attach the wheel guard with side guard (sold
separately). (Fig. 1)
01Eng_G13YC2_WE 1/17/12, 8:289
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi G13YC2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi G13YC2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info