390436

Hitachi g 23 se2 Manual

23
Zoom out
Zoom in
Previous page
1/37
Next page
22
English
SPECIFICATIONS
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 Weight: Only main body
*3 The starting current limiter produces the starting current to such an extent that a fuse (16A, slow-blow)
is not tripped.
STANDARD ACCESSORIES
(1) Wrench ........................................................................ 1
(2) Side handle ................................................................ 1
Depressed center wheels are not provided as standard
accessories.
Standard accessories are subject to change without
notice.
APPLICATIONS
⅜
Removal of casting fin and finishing of various types
of steel, bronze and aluminum materials and castings.
⅜ Grinding of welded sections or sections cut by
means of a cutting torch.
⅜ Grinding of synthetic resins, slate, brick, marble, etc.
⅜ Cutting of synthetic concrete, stone, brick, marble
and similar materials.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent
injury should the depressed center wheel shatter
during operation. Ensure that the guard is properly
fitted and fastened before commencing grinding
operation.
[Installing and adjusting the wheel guard]
⅜ Open the lever and insert the locating pin of wheel
guard, bringing it into line with the across flats of
packing ground.
⅜ Then, turn the wheel guard to a desired position
(for use).
⅜ Close the lever and fix it. If and when required,
carry out adjustments by tightening or loosening
the screw.
⅜ If the lever does not move smoothly, apply some
lubricating oil to the sliding section between the set
piece and the lever.
⅜ Fasten the wheel guard at the position where the
across flats of the wheel guard positioning pin and
packing ground are aligned (the position where the
wheel guard is inserted), but do not use it.
5. Ensure that the depressed center wheel to be utilized
is the correct type and free of cracks or surface
defects. Also ensure that the depressed center wheel
is properly mounted and the wheel nut is securely
Model G18SE3 G18UA2 G18SG2 G18UB2 G23SC3 G23UA2 G23SE2 G23UB2
Voltage (by areas)*
1
(110V, 220V, 230V, 240V)
Input*
1
2300 W 2500 W 2300 W 2500 W
No-load speed 8500 min
-1
6600 min
-1
Outer dia. 180 mm 230 mm
Wheel Inner dia. 22 mm
peripheral speed 80m/s
Weight*
2
5.0 kg
Starting current limiter*
3
No Yes No Yes No Yes No Yes
PRECAUTIONS ON USING DISC GRINDER
1. Never operate these power tools without Wheel
Guards.
2. Check that speed marked on the wheel is equal
to or greater than the rated speed of the grinder.
Use only a depressed center wheels rated at
80 m/s or more.
3. Ensure that the wheel dimensions are compatible
with the grinder and that the wheel fits the spindle.
4. Abrasive wheels shall be stored and handled with
care in accordance with manufacturer’s
instructions.
5. Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products.
6. Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
7. Do not use cutting-off wheels for side grinding.
8. Do not use of separate reducing bushings or
adapters to adapt large hole abrasive wheels.
9. The wheel continues to rotate after the tool is
switched off.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitachi g 23 se2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi g 23 se2 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info