Manual Hitachi FSV10SA (page 7 of 44) (English, German, Dutch, French, Italian, Portuguese, Spanish)

567010

Zoom out

Zoom in

1/44

English

4. After installing new sanding paper

Movement of the sander may tend to become

unsteady after new sanding paper has been installed,

because of the new, coarse grain of the paper. This

can be avoided by slightly tilting the sander forward

or backward during sanding or polishing. Sander

movement will become steady as the sanding paper

surface becomes properly abraded.

5. Using commercial sanding paper having no holes

Obtain 230 × 280 mm sanding paper and cut into 3

equal longitudinal portions (Fig. 5).

Before using, make holes in the sanding paper to

boost its dust absorbing efficiency.

To make the holes (perforations), align the sanding

paper with the guide in the accessory punch plate

and apply pressure (Fig. 6).

MOUNTING THE OPTIONAL ACCESSORIES

1. Attaching a sponge pad (magic type) or a stick-on

pad

Loosen the M4 × 10 screws (4) and remove the

attached pad. Next, attach a sponge pad (magic type)

or a stick-on pad.

CAUTION

Replace the pad only. Use the other parts without

removing them.

2. Attaching magic type sanding paper or stick-on type

sanding paper

Match the sanding paper’s hole with the pad’s hole

and strongly push the sanding paper with the palm

of your hand to fasten it securely in place.

MAINTENANCE AND INSPECTION

1. Empting and cleaning the Dust Bag

If the dust bag contains too much saw dust, dust

collection will be affected. Empty the dust bag when

it gets full.

Remove the dust bag, open the fastener, and dispose

of the contents.

2. Inspecting the sanding paper

Since use of worn-out sanding paper will degrade

efficiency and cause possible damage to the pad,

replace the sanding paper as soon a excessive

abrasion is noted.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

4. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must

be returned to Hitachi Authorized Service Center for

the cord to be replaced.

6. Servicing

Consult an authorized Service Agent in the event of

power tool failure.

7. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal

marked with the letter L or coloured red. Neither core

must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

01Eng_FSV10SA_WE 11/27/08, 15:086

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi FSV10SA in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi FSV10SA Manual

Product: