Manual Hitachi fds 9 dva (page 24 of 29) (English, Danish, Swedish, Norwegian, Finnish)

387444

Zoom out

Zoom in

1/29

English

off to indicate that the battery is fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than two hours have elapsed after starting of the

charging, stop the charging and contact your

HITACHI AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light up. At that time, cool the battery

first, then start charging.

3. Disconnect the charger power cord from the

receptacle.

4. Hold the charger tight and pull out the battery.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by follow-

ing the precautions.

HOW TO USE

1. Confirm the cap position (See Fig. 4)

The tighthening torque of this unit can be adjusted

according to the cap position, at which the cap is

set.

(1) When using this unit as a screwdriver, line up the

one of the numbers “1, 3, 5 … 22” on the cap, or

the black dots with the triangle mark on the outer

body.

(2) When using this unit as a drill, align the cap drill

mark “

” with the triangle mark on the outer

body.

CAUTIONS

⅜ The cap cannot be set between the numerals “1,

3, 5 … 22” or the black dots.

⅜ Do not use with the cap numeral between “22” and

the black line at the middle of the drill mark. Doing

so may cause damage. (See Fig. 5)

2. Tlightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

used, the screw head may be broken or be damaged.

Be sure to adjust the cap position according to the

screw diameter.

(2) Tightening torque indication

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 … 22” on the cap, and the black

dots. The tightening torque at position “1” is the

weakest and the torque is strongest at the highest

number. (see Fig. 4).

(3) Adjusting the tightening torque

Rotate the cap and align the numbers “1, 3, 5 …

22” on the cap, or the black dots with the triangle

mark on the outer body. Adjust the cap in the weak

or the strong torque direction according to the

torque you need.

CAUTION

⅜ The motor rotation may be locked to cease while

the unit is used as a drill. While operating the driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening force.

3. Change rotation speed

Operate the shift knob to change the rotation speed.

Move the shift knob in the direction of the arrow

(see Figs. 6 and 7).

When the shift knob is set to “LOW”, the drill

rotates at a low speed. Whe set to “HIGH”, the drill

rotates at a high speed.

CAUTION

⅜ When changing the rotation speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is “17” or “22”, it may

happen that the clutch does not engage and that

the motor is locked. In suh a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt out.

4. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

in Table 1.

Table 1

Work Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi fds 9 dva in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi fds 9 dva Manual

Product: