Manual Hitachi fds 10 dv (page 8 of 38) (English, German, Dutch, French, Italian, Portuguese, Spanish)

386508

Zoom out

Zoom in

1/38

English

(2) Tightening power indication

Tightening power should be changed according to

the screw type and the materials to be tightened.

Guidance of the tightening power is indicated on

the outer frame of this unit with numerals “1”, “2”,

“3”, “4” and “5”. The minimum power is from “1”

position and bigger the value the stronger is the

power (see Fig. 5).

(3) How to adjusts the tightening power

Rotate the cap and set to one of the numerals.

Adjust the power by cap rotation in such a way that

when the power is too strong, set to the next

smaller numeral and set to the next larger numeral

when too weak.

CAUTION

⅜ The motor rotation may be locked to cease while

the unit is used as drill. While operating the driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational

speed. Move the shift knob in the direction of the

arrow (see Figs. 6 and 7).

When the shift knob is set to “L”, the drill rotates

at a low speed. When set to “H”, the drill rotates

at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “H” (high speed) and

the position of the cap is “4” or “5”, it may happen

that the clutch does not engaged and that the motor

is locked. In suh a case, please set the shift knob

to “L” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt.

4. The scope and suggestions for uses

The usable scope for various types of work based

on the mechanical structure of this unit is shown

in Table 1.

CAUTION

⅜ The selection examples shown in Table 2 should

be considered as general standard. As different types

of tightening screws and different materials to be

tightened are used in actual works proper

adjustments are naturally necessary.

6. Mounting and dismounting of the bit.

(1) Mounting the bit

After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front). (See Fig. 8)

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counterclockwise

direction as viewed from the front). (See Fig. 8)

Use Cap Position

Rotating speed selection (Position of the shift knob)

L (Low speed) H (High speed)

Machine screw 1–5

For 4mm or smaller diameter For 5mm or larger diameter

Driving

screws. screws.

Wood screw 1–5

For 3.5mm or smaller nominal For 3.8mm or larger nominal

diameter screws. diameter screws.

Wood For 10mm or larger diameters.

For 10mm or smaller

Drilling

diameters.

Metal

For drilling with an iron

————————

working drill.

Table 2

5. How to select tightening power and rotational speed

Work Usable range Suggestions

Wood: 15mm

Drilling Steel: 10mm Use for drilling purpose.

Aluminum: 10mm

Machine screw: 6mm

Use the bit and socket matching the screw

Driving Nut: 5mm

diameter.

Wood screw: 5.1mm (diameter) × 32mm (length)

Use after drilling a preparatory hole.

Table 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hitachi fds 10 dv in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hitachi fds 10 dv

Hitachi fds 10 dv User Manual - English, Danish, Swedish, Norwegian, Finnish - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hitachi fds 10 dv Manual

Product: